A heating device contains 5 kg water and is being heated. During the process, 11 kJ/kg of heat is transferred to the water, and heat losses from the walls amount to 8 kJ. And 5 kl of work is done by the vapor. Determine the change in the energy of the water for this process.

A heating device contains 5 kg water and is being heated. During the process, 11 kJ/kg of heat is transferred to the water, and heat losses from the walls amount to 8 kJ. And 5 kl of work is done by the vapor. Determine the change in the energy of the water for this process.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 17RQ: At a constant pressure, how does a volume of gas vary with respect to the absolute temperature?

See similar textbooks

Related questions

Q: The solid circular rod has a cross-sectional area of 450 mm2. It is subjected to a uniform axial dis...

Q: The truss shown consists of wooden members. Knowing that each member has a 100 x 100 mm. square cros...

Q: 16. A bullet with mass of 0.075 kg is fired to a stationary block with mass of 4 kg with an initial ...

A: To find Vertical distance(d) travelled by block

Q: The 4.2 Mg truck and 2.0 Mg car are traveling with the free-rolling velocities shown just before the...

Q: Take the following data for the syringe injection pump Inner diameter of syringe barrel: D = 1.5 cm ...

A: The inner diameter of the syringe barrel D = 1.5 cm Inner diameter of the needle shaft of the syring...

Q: Problem 2. A compound gear train as shown in the following figure, Gear 1 has 24 teeth and Gear teet...

Q: 85 35 55 115 35 125

Q: 10. The glass tube in figure below is used to measure pressure p, in the tank. The tube diameter is ...

Q: Q 1: Find the Centroid of the Lamina in Fig. 1. (All units are in mm)

Q: Q. 374. What is the difference between flow variable and coefficient of flow variable in hydrodynami...

A: A flow variable is mathematically defined as the ratio of flow of lubricant within the clearance to ...

Q: Determine maximum spring compression

A: Given: R=0.7 m b=1 m k=0.8 N/m μ=0.2 TO determine: The compression in spring

Q: natural strain at point B

A: Given; Figure shows the true stress and true strain hardening material.Point A is loading up point.i...

Q: Name the material's strengthening mechanism behind each of the following phenomena: (1) Si alloyed a...

A: Si alloyed aluminium has higher strength, its not major alloying element. It just decrease the melti...

Q: For the simply supported beam shown below, determine the internal resultant loadings at point 0.5 me...

A: It is required to determine internal reaction force at 0.5 m left to point C

Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something. Technic...

A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior micromet...

Q: Determine the strain if a rod is experiencing a stress of 70,000 kPa with a modulus of elasticity of...

A: Determine the strain

Q: An axial flow water pump impeller consists of 5 blades with chord length 3 in., hub radius 4.5 in. a...

Q: small ball slides around a horizontal circle at height y inside a frictionless emispherical bowl of ...

A: HHjajja

Q: For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are respecti...

A: As given in the question, Maximum stress in the cycle = σmax = 250 MPa Minimum stress in the cycle =...

Q: A block chutch has four wooden shoes each contacting with 80 degrees of the inside of a 13-in drum T...

A: Number of wooden shoes, k= 4 Angle of contact, 2θ= 80∘ ⇒ θ= 40∘ Diameter of the drum, D= 13 in Hence...

Q: A solid steel shaft is to be used to transmit 5 hp from the motor to which is attached. If the shaft...

Q: A circular deep dish has a sharp-edged hole in its center. A jet of water speed V, hit the plate co...

Q: Suppose a heat engine is made out of an ideal diatomic gas taken around a cycle represented by the f...

A: (a) The Pv diagram shown here represents a reversible process. This diagram represents a sudden chan...

Q: natical model that gives the variation of the tempen mic conditions. tial and boundary conditions to...

A: data given copper (k =40 W/m.°c)cross section area A=1m2then heat transfer rate through th...

Q: MABP is a straight line and the following observations were made. Angle DAM 70° 19' 00" Angle CBP 56...

Q: Steam at a temperature of 250°C has a specific volume of 0.15436 m3/kg. What is the pressure in MPa?

A: Given data, T = 250°C v = 0.15436 m3/kg Find P = ?

Q: A particle is moving along a circular path with tangential acceleration function of a(t) = (0.12t + ...

Q: Solve the following system of nonlinear equations for x, y, and z. x + y + z? = 6 x² - y + 2z? = 2 2...

Q: In the figure below, the losses up to section A is 5V,2/2g and the nozzle losses are 0.05V," /2g Det...

A: Given data as per question Height H =8 m D1 =150 mm D2 =50 mm calculations Water is incompressible c...

Q: 8.1 Find the total delta-v required for a Hohmann transfer from earth's orbit to Saturn's orbit. [An...

A: To Determine The total delta-v required for a Hohmann transfer from earth's orbit to saturn orbit. ...

Q: what is the shear and moment diagram for the cantilivered beam below measured from the free end

Q: 11.2 (USCS units) A horizontal true centrifugal casting oper- ation is performed to make cast iron p...

Q: Experimental Techniques for Identification of Microstructure and Defects?

A: Microstructure of a material is its appearance at the nanometer scale. Real world materials always p...

Q: Q3: A: A half circle of area made from wood, while the other half made from metal. Can you consider ...

Q: 1. A water tube boiler operates at 1100 psia has the following characteristics: No. of riser 100 Ris...

A: Given DataP=1100Psiat=0.22 inDowncomer Length=75 ftchange in length=80-75=5ft=d

Q: QI: The cable AB supports three vertical loads as shown in next figure. Compute the resultant of the...

A: A cable with three downward forces is provided. Find the resultant of these forces, as well as its l...

Q: ta motor drives a solid 3/8" diameter steel shaft at 3,600 RPM, see Fig. below. Calculate the follow...

Q: A compressed air tank has a volume of 0.85 m3. When the tank is filled with a gauge pressure of 3 ba...

Q: An inventor claims to have designed a steam turbine that takes in 2.78lb/sec of steam at 725 psia an...

A: Given: pressure at the inlet of the turbine→pi=725 psia=144×725=104400 lbfft2 pressure at the exit ...

Q: What is the hardest metal? What is it's Vicker's Hardness score?

Q: Discussion Explain how the stationary fluid flours when it becomes in touch with heated wall. You ma...

A: Soln:- Heat is transferred from the hot water to the cold water until both samples have the same te...

Q: to cause the disk to rotate. To make the computation easier, let us assumee that the arm does nott r...

Q: A heat pump supplies heat energy to a house in order to maintain its temperature at 20°C. Over a per...

Q: Q1: The cable AB supports three vertical loads as shown in next figure. Compute the resultant of the...

Q: A centrifuge bowl is to separate two immiscible liquids, one with SG 1.1 and the other with SG 0.9. ...

Q: What are crumple zones in cars designed for? absorbing the shock from bumpy roads changing the direc...

A: Please see the solution below

Q: 1) Reaction at 'B' in N. 2) Force in link 'DE' in N. 3) Horizontal component at 'C' on member 'BCD' ...

Q: How can we apply physical activity in any field of specialization? example in engineering field

A: In Mechanical Engineering field,I share a interesting story where a physical activity is used.I live...

Q: (a) Which of the following is the horizontal resultant of the forces given? 89.33 N (b) Which of the...

Q: The engine of the helicopter is delivering 600 hp to the rotor shaft when the blade is rotating at 1...

A: The radius are calculated for both the conditions and bigger radius is considered for final selectio...

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

A heating device contains 5 kg water and is being heated. During the process, 11 kJ/kg
of heat is transferred to the water, and heat losses from the walls amount to 8 kJ. And
5 kJ of work is done by the vapor. Determine the change in the energy of the water for
this process.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider an insulated system with piston and cylinder arrangement in which Oxygen gas is present. If the change in internal energy of the gas is 100 kJ, then the work given on the gas is _________
During an expansion process, the pressure of a gas changes from 15 to 100 psia according to the relation P = aV + b, where a = 5 psia/ft3 and b is a constant. If the initial volume of the gas is 7 ft3 , calculate the work done during the process.
A frictionless piston–cylinder device contains 10 lbm of steam at 60 psia and 320°F. Heat is now transferred to the steam until the temperature reaches 400°F. If the piston is not attached to a shaft and its mass is constant, determine the work done by the steam during this process.
How does useful work differ from actual work? For what kinds of systems are these two identical?
A frictionless piston–cylinder device initially contains 170 L of saturated liquid refrigerant-134a. The piston is free to move, and its mass is such that it maintains a pressure of 900 kPa on the refrigerant. The refrigerant is now heated until its temperature rises to 70°C. Calculate the work done during this process.
A rigid vessel contains 5.0 kg of wet steam at 0.4 MPa. After the addition of 9585 kJ the steam has a pressure of 2.0 MPa and a temperature of 700°C. Determine the initial internal energy and the specific volume of the steam.
A cylinder fitted with a piston has a volume 0.1 m3 and contains 0.5 kg of steam at 500 kPa. How much heat is to be supplied to bring the temperature of the steam to 823 K keeping the pressure constant? What is the work done in the process? Answer: Q = 914.86 kJ, W = 139.35 kJ
A 0.75-m3rigid tank initially contains air whose density is 1.18 kg/m3 The tank is connected to a high-pressure supply line through a valve. The valve is opened, and air is allowed to enter the tank until the density in the tank rises to 4.95 kg/m3. Determine the mass of. air that has entered the tank.
1.5-lbm of water at 350 psia fill a weighted piston-cylinder device whose volume is 1 ft3. The water is then heated at constant pressure until the temperature reaches 550◦F. Determine the resulting change in the water’s total entropy.
Q1/ A frictionless piston–cylinder device initially contains 200 L of saturated liquid refrigerant-134a. The piston is free to move, and its mass is such that it maintains a pressure of 900 kPa on the refrigerant. The refrigerant is now heated until its temperature rises to 70°C. Calculate the work done during this process. Answer: 5571 kJ
A student living in a 4 - m 5 - m 3 - m dormitory room turns on her 100 - W fan before she leaves the room on a summer day, hoping that the room will be cooler when she comes back in the evening. Assuming all the windows are tightly closed and disregarding any heat transfer through the walls and the windows, determine the temperature in the room when she comes back 8 h later. Use specific heat values at room temperature, and assume the room to be at 100 kPa and 20 ° C in the morning when she leaves.
A 2-m3 rigid tank initially contains air whose density is 1.18 kg/m3 . The tank is connected to a high-pressure supply line through a valve. The valve is opened, and air is allowed to enter the tank until the density in the tank rises to 5.30 kg/m3 . Determine the mass of air that has entered the tank.