A high-strength steel bar used in a large crane has a diameter d- 4.00 in. (see figure). The steel has a modulus of elasticity E - 28 x 10° psi and Poisson's ratio is v = 0.28. Because of clearance requirements, the diameter of the bar is limited to 4.002 in. when it is compressed by axcial forces. What is the largest compressive load Pmay that is permitted? Assume that the material behaves linearly elastically. (Enter the magnitude in Ib.)

A high-strength steel bar used in a large crane has a diameter d- 4.00 in. (see figure). The steel has a modulus of elasticity E - 28 x 10° psi and Poisson's ratio is v = 0.28. Because of clearance requirements, the diameter of the bar is limited to 4.002 in. when it is compressed by axcial forces. What is the largest compressive load Pmay that is permitted? Assume that the material behaves linearly elastically. (Enter the magnitude in Ib.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If possible, answer in 3 decimal places, thank you. For the wood beam shown in Figure A, assume L=1.5 m and P=8 kN. The beam cross section shown in Figure B has dimensions of b=47 mm and d=232 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? Calculate the reaction forces By and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown for the forces By and Dy on the free-body diagram below. (Note: Since Dx=0, it has been omitted from the free-body diagram.) By= kN Dy= kN Determine the shear forces VA⁢B, VB⁢C, and VC⁢D acting in segments AB, BC, and CD, respectively. Note that the shear force is constant in each of these segments. When entering your answers, use the shear force sign convention. VA⁢B= kN VB⁢C= kN VC⁢D= kN…
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 0.9 GPa. Each bar has a cross-sectional area of 1050 mm2. Using L = 395 mm and Δ = 7.3 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? [Answer: P = 67.0 kN]
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
A 3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 kN. Poisson’s Ratio = 0.25 and E = 200 000 MPa. Compute the lateral strain. Express your answers in 6 decimal places.
a tubular steel strut of length 1.2 m , inner diameter 100mm and outer diameter 180mm carries a compressive load of 3.5 MN. If poissons ratio for the material is 0.33 and the modulus of elasticity is 214 E GPA . determine the change of length and outer diameter of the column.
The reinforced concrete beam has the cross-sectional area shown in the figure with b =12 in., d=16 in., ? steel= 1.571 in.2, determine the largest bending moment that may be applied safely. Takethe elastic moduli ?steel=29(10^3) ksi and ?concrete= 3.6(10^3) ksi. The working stresses are2.39ksi for concrete and 22.145ksi for steel.
A prestressed concrete beam is simply supported over a span of 11 m. the beam is reinforced with straight tendons situated as shown in the figure under a prestressing force of 682 kN. The beam is carrying a live load of 16.14 kN/m2 and a dead load of 22.09 kN/m2 excluding its own weight, Concrete weighs 20.39 kN/m3 with modulus of elasticity Ec=17,459.32 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads. (Include the sign if it is negative) Always write your answer in 4 decimal places
Q2 / The reinforced concrete beam has the cross - sectional area shown in figure if it subjected to a bending moment of M = 60 kips.ft, determine the normal stress in each of the steel reinforcing rods and the maximum normal stress in the concrete. Take Est = 29 * 10% ksi and Ec = 3.6 * 10 ° ksi.
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 1. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
The cross section of a concrete corner column that is loaded uniformly in compression is shown in the figure. A circular pipe chase cut-outof 10 i n. in diameter r tins t he height of t he co \u m n (see figure).(a) Determine the average compression stress crr in the concrete if the load is equal to 3500 kips.(b) Determine the coordinates x and y{of the point where the resultant load must act in order to produce uniform normal stress in the column.
A beam with a T-section is supported and loaded as shown in the figure. The cross section has width b = 2 1/2 in., height h = 3 in., and thicknesst =3/8 in.(a) Determine the maximum tensile and compressive stresses in the beam.(b) If the allowable stresses in tension and compression are 18 ksi and 12 ksi, respectively, what is the required depth h of the beam? Assume thatthickness t remains at 3/8 in. and that flange width b 5 2.5 in.(c) Find the new values of loads P and q so that the allowable tension (18 ksi) and compression (12 ksi) stresses are reached simultaneously forthe beam. Use the beam cross section in part (a) (see figure) and assume that L1, L2, and L3 are unchanged.