A hollow metal tube with an inside diameter of 265 centimeters must carry a tensile load of 910kN. Determine the outside diameter of the tube, in meters, if the stress is limited to 171

Q: Calculate the maximum moment (with diagram) &  maximum shear (with diagram)

A:

Q: Classify the following soil according to the Unified System: 2% of the material is retained on the N...

A: Given % retained on seive #4 = 2% %Passing seive #4 = 90% %Passing seive #200 = 8% LL = 45% PL = 31%...

Q: Exercise For Practice 924 $12 30 50 FV X

A: Isometric Projection: Isometric Projection is a type of pictorial projection in which the three dime...

Q: Write the shear and moment equations (not simplified and simplified) at each segment of the beam. Dr...

A:

Q: The lap joint in the figure is fastened by four 20 mm Ø A325X bolts. Calculate the maximum safe load...

A:

Q: 5. When deslgning hydraulic structures, like brldges, what procedure might reduce total costs? a. De...

A: There exist many criteria in design of hydraulic structures that need to be optimized simultaneously...

Q: A water jet of velocity 4.2 m/s and a cross-sectional area of 0.50 m2 strikes a curved vane, as show...

A: Data given Flow velocity, V = 4.2 m/s Area of flow, A = 0.5 m2 Angle of split = 540 Solution Flow ...

Q: In May 1970, a 70 ft tall, 20 ft diameter concrete grain silo was constructed at a site in EasternCa...

A: Step 1: qu =7.4 x 500 + 80 x 4=4020 lb/Sq ft Q= 4020 X 3.14 (11.82-1.52) Q=1729197 Lbs= 7,691.851584...

Q: Calculate for support reactions if: P=51 -Plot shear diagram -Plot moment diagram

A:

Q: 5. Determine the force in members HG, HE, and DE of the truss, and state if theA members are in tens...

A:

Q: Cable Analysis : Analyze the loaded cables as shoon. TOO m 10 m 40 kg/m

A: cable is subjected to uniform vertical  load  so horizontal force at each joint will be equal and in...

Q: Given data : Water content3D0.3 Void ratio=0.25 Specific gravity=2.7 Determine degree of saturation

A: Given data : Void ratio of soil (e)=0.25 Water content of soil (w)=0.3 Specific gravity of soil soli...

Q: If the block is 1000jg, determine the value of force P(N) that is causing the movement of the block ...

A: Given: The mass of the block is 1000 kg. The coefficient of static friction is 0.50. The coefficient...

Q: The maximum tension in the steel rod is 580 N and the maximum stress in the link is 30 N/mm2.

A:

Q: Cable Analycis: Analyze the loaded cables ac dhoon. TO0m I0 m 1om 40 kg/m

A: To Analyse the cable we need to calculate the reactions at the ends(H,RA and RB) also calculate Maxi...

Q: The maximum tension in the steel rod is 580 N and the maximum stress in the link is 30 N/mm2. I1 sid...

A:

Q: The maximum tension in the steel rod is 580 N and the maximum stress in the link is 30 N/mm2. I side...

A:

Q: A mass weighing 9lb stretches a spring 4in. If the mass is pushed upward, contracting the spring a d...

A: For the given conditions, the position u(t), frequency, period, amplitude, and phase of the motion h...

Q: Find an angle in degree unit that measures 24 degrees more than twice its supplement. Select one: О ...

A:

Q: SANITARY PLANNING LAYOUT " F. SYMBOLS AND LEGENDS

A:

Q: Determine the design compressive strength (kips) of a A36 steel column, W 10 X 33 with a total lengt...

A:

Q: Determine water if degree of saturationis 0.7, Void ratio is 0.5 and specific gravity of soil solid ...

A:

Q: 1. To determine the area of a triangular lot ABC, a surveyor set-up a transit at point P inside the ...

A:

Q: A simply supported beam with P1=60 kN, P2=53 kN and w-25 kN/m has the loadings shown. If the value o...

A: As per company's guidelines  We can only answer first question Kindly post other question as separat...

Q: The cantilever beam carries a triangular load, the intensity of which varies from zero at the left e...

A:

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine w...

A: Please find the answer in the below attachments 

Q: Determine the force required to produce stress of 20 N/m2 on cross sectional area of 5 m2

A: Given data : Cross sectional area (A)=5 m2 Stress produced σ=20 N/m2   Required : Force  We know tha...

Q: Assuming concrete below the neutral axis to be cracked, the shear stress across the depth of a singl...

A:

Q: Determine water if degree of saturationis 0.7, Void ratio is 0.5 and specific gravity of soil solid ...

A: wG=Se w= water content G= specific gravity e=void ratio S=degree of saturation w= Se/G w= (0.7*0.5)/...

Q: 21mm 4mm 38mm 16 mm 21mm 2.

A:

Q: Find the forces (kN) on the members of the given truss. Determine also the magnitudes of the support...

A:

Q: Determine the required diameter of a plug weld using E60 electrodes on A-36 steel to develop the ful...

A: We have to determine the value of required diameter of a plug weld using E60 electrodes on A36 steel...

Q: S0KN E 25kN 6m 30KN 6m An 5m | Ap By

A:

Q: 6. Sample of standard brick, it's absorption equal to 17% and specific gravity equal to 1.65 the per...

A:

Q: Determine the design compressive strength (kips) of a A36 steel column, W 10 X 33 with a total lengt...

A:

Q: aggregates, water, and cementitious materials: cement and fly ash. The ratio of fine and coarse aggr...

A:

Q: Problem 3: A pump is place in a pipe system, the system equation/energy equation is given by h, =15+...

A:

Q: Prob. 1.4-19. A vertical force P = 10 kips acts downward at the apex B of frame ABC, as shown in Fig...

A:

Q: A high-strength steel band saw, 22 mm wide, runs over pulleys 1100 mm in diameter. What minimum thic...

A:

Q: When a specimen of M25 concrete is loaded to a stress level of 12.5 MPa, a strain of 500x10^-6 is re...

A:

Q: Determine plasticity index if liquid limit is 40% and plastic limit is 30%

A: Introduction : Plasticity index is equal to difference between liquid limit and plastic limit . The ...

Q: A 500 mm square concrete column carries a factored ultimate vertical column load of780 kN. The verti...

A: as the nominal shear stress coefficient is not given we consider only moment criteria here and calcu...

Q: the flooring material in the following locations? A. Check-out area B. Greenhouse sales C

A: 1.Check-out area  Acrylic and epoxy resin flooring is the good choice for the check-out area because...

Q: 50 kN-m 4 m El = constant

A:

Q: A 30 ft wide UV treatment tank has a serpentine weir to regulate flow depth. The forks of the weir a...

A: Given:- The width of the UV treatment tank = 30 ft The forks of the weir = 1.5 ft wide The length of...

Q: The cantilever beam carries a triangular load, the intensity of which varies from zero at the left e...

A:

Q: determine the yield angle of twist (in radians) in the rod

A:

Q: Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft³) behaves as a liquid. Determine the forc...

A: The given data is: sw=150lb/ft3 Height of concrete in form=9 ft Force on form Ft=sw×z×A  

Q: Shown below is a beam carrying a uniform load and two vertical forces at points B and D as shown in ...

A:

Q: Problem-1 A soil sample, taken from a borrow pit has a specific gravity of soil solids of 2.65. The ...

A: Optimum moisture content, OMC is the water/moisture content at which the soil attains maximum dry de...

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.