a) If the counter-eletromotive force Eo-80V when the motor reaches speed n=1000rpm, calculate what is the current in the armature at this time? b) What was the current in the armature right before the start of the motor, when speed n=0rpm? c) Draw the graph of current vs. speed from start to steady state, if the maximum speed n=1,875rpm. Es=160V R=20 Ohms Es 1 R

a) If the counter-eletromotive force Eo-80V when the motor reaches speed n=1000rpm, calculate what is the current in the armature at this time? b) What was the current in the armature right before the start of the motor, when speed n=0rpm? c) Draw the graph of current vs. speed from start to steady state, if the maximum speed n=1,875rpm. Es=160V R=20 Ohms Es 1 R

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

We know that synchronous motor runs in a same speed no matter what the load is. There is another motor that exhibits almost the same kind of characteristics. Write the name of the motor.
A 400V D.C. shunt motor takes 5 A at no-load. R = 0.5 ohms, R,= 200 ohms. What is the ratio %3| %D a f of speed from full load to no-load, when the D.C. shunt motor takes 50 A on full load? (b) 0.8 (d) 0.4 (а) 0.94 (c) 0.6
7. A 4-pole, 500V shunt motor has 720 wave connected conductors on its armature. The full-los armature current is 60A and flux per pole is 0.03 Wb. The armature resistance is 0.020 and th contact drop per brush is 1V. then the full-load speed of the motor is -- a) 675 r.p.m. b) 690 r.p.m. c) 705 r.p.m. d) none of the previous,
The armature winding resistance of a 200 Volt 4-pole DC motor is 2 ohms. Under full load, the armature current of the motor is up to 10 A. Armature coil is parallel wound and has 360 conductors. Since the magnetic flux under the pole foot of the motor is 12.5 mWb, which of the following is the motor speed? a 2100 rpm b. 2400 rpm C. 2500 rpm d.2300 d min
A 4 pole, Lap wound d.c motor has 540 conductors. Its speed is found to be 1000 r.p.m. when it is made to run light. The flux per pole is 25 mWb. It is connected to 230 V d.c. Supply.The armature resistance is 0.8N Calculate. i) Induced e.m.f ii)Armature current iii) stray losses iv) Lost torque
A 4-pole, lap wound DC shunt generator with 0.05 Wb per pole, the armature consists of 100 slot, each slot contain 6 conductors, the speed at which it is to be driven to generate 460 V is .* O 1840 r.p.m O 920 r.p.m O 506 r.p.m O 253 r.p.m
Describe the similarities in the construction of a DC motor and a DC generator. Please answer in short point wise and dont copy from other sources i will like lt
Q/ During the test of shunt excited generator the voltage initially must be adjusted to 220V. then the generator is loaded and the motor field circuit resistance is ........... adjusted to 1/ Increase the speed. 2/ Reduce the speed 3/ Keep the speed constant 4/ To control the voltage. 5/ None of the mentioned
State two reasons why a self-excited shunt dc generator may fail to build up a voltage. In each (both) case, briefly explain what can be done to correct the problem. Reason #1 Solution #1 Reason #2 Solution #2
A. The DC motor in Figure 3 on Worksheet 8 is aa) cumulatively connected short-shunt compound DC motor b) cumulatively connected long-shunt compound DC motor c) differentially connected short-shunt compound DC motor d) shunt DC motorB. Is the DC motor in Figure 1 on Worksheet 8 turning in the same direction as that in Figure 3?a) yes b) no
A DC shunt motor takes an armature current of 20A at 800V, It has an armature resistance of 0.06 ohms and field resistance of 120 ohms. The machine has 8-poles and armature is lap connected with 964 conductors with a full load speed of 836 rpm. Calculate the line current and flux per pole. Select the correct response: 0.10 Wb and 10.22A 0.14 Wb and 12.44A 0,05 Wb and 14.58 A 0.15 Wb and 13,33A
2 a. The back-EMF generated by a DC motor is greatest when the motor is a) standing still b) running at full-load c) running with no-load d) none of the above b. Which of the following is/are considered a loss of a DC motor? a) power losses in the armature and field b) windage c) friction d) all of the above c- When it is said that a motor has good speed regulation it means the motors speed changes__________ from no-load to full-load. a) little b) a lot c) tremendously d) none of the above