A juice box measures 6.4 cm (W) by 4.0 cm by 10.5 cm(H). It contains 250 ml of juice. The straw height (distance from the bottom of the box to the spout) is (H)+0.5 cm. The straw diameter is approximately 1.6 cm(D). I KNOW THIS IS NOT EXACTLY HOW THIS WORKS, but assume the box does not deform very much and treat my nephew squeezing the juice box as if we are adding a little pump to the system. If the applied head from my nephew's hand is (40) cm(P), what is the exit velocity out of the straw? State all your assumptions. H am

A juice box measures 6.4 cm (W) by 4.0 cm by 10.5 cm(H). It contains 250 ml of juice. The straw height (distance from the bottom of the box to the spout) is (H)+0.5 cm. The straw diameter is approximately 1.6 cm(D). I KNOW THIS IS NOT EXACTLY HOW THIS WORKS, but assume the box does not deform very much and treat my nephew squeezing the juice box as if we are adding a little pump to the system. If the applied head from my nephew's hand is (40) cm(P), what is the exit velocity out of the straw? State all your assumptions. H am

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Similar questions

6. Two 8 x 4 x 1 inch blocks of foam are glued together (one block on top of the other) and used to support the bottom face of a product. The product weights 15 pounds. The stiffness of each of the blocks respectively is 50 lb/in and 25 lb/in. When the product is placed on the blocks of foam ... a) What is the total foam deflection? b) What is the static load on the foam block? c) What is the natural frequency of the total system?
1. What is the other name of the dry granulation method? 2. What is the process of liquefaction of solids when mixed? 3. What is the process of amassing material fines into cohesive units like pellets or granules? 4. What is the process of reducing particle size of a solid by first forming a mass with a liquid, then grinding with a mortar and pestle? 5. What kind of paper packaging is semi-opaque with limited moisture resistance? 6. Which blending process has low homogeneity? 7. Which method is used to ensure the uniform distribution of the potent drug? 8. What powders will absorb moisture from the air to the extent that they will partially or completelt liquefy? 9. What kind of paper packaging is semi-opaque with limited moisture resistance?
1. Given the results of an Atterberg limit test. Complete the test report which will include filling out the two tables, plotting the Liquid Limit results and finding the Water Content, the Plastic Limit, the Liquid Limit, and the Plasticity Index. Use a ruler when hand drawing the line or when finding the points in the graphic to achieve good precision. W PL PL PL Type of test Container No. 1 2 3 4 Wet wt + container 15.50 4.92 4.54 5.70 12.50 4.23 3.92 4.81 Dry wt + container Wt of water Wt of container Dry wt of soil Water content% 2.10 1.50 1.51 1.45 Container No. 5 7 8 No. of blows 30 20 14 Wet wt + container 5.25 5.35 4.80 Dry wt + container 4.26 4.25 3.73 Wt of water Wt of container 1.67 1.59 1.49 Dry wt of soil Water content% 50% 45% W 40% LL 35% PL € 30% PI 25% 20% Water Content% 10 20 30 40 Number of Blows 50 6525 45 4.25 3.55 1.53 100
Determine plasticity index if liquid limit is 40% and plastic limit is 30%
Design Problem, a horizontal separator for the following operating conditions. Gas rate: 15 MMSCFD Gas specific gravity: 0.6 Oil rate: 4,000 bbl/day Oil gravity: 40 API Operating pressure: 1000 psi Operating temperature: 60F Retention time: 3min Droplet size removal: 120 µm d Liquid Leff 20 24 30 36 42 46 No 2 Gas Leff LISS Hg=0.013 CP Pg=3.708 lb/ft³ Po= 53.03 lb/ft³ Z=0.84 SR 15 marks)
4. MECHANICAL SEPARATION A sieve analysis gives the following results: Sieve size (mm) Wt. retained (g) 1.000 0 0.500 64 0.250 0.125 0.063 324 240 48 24 Through 0.063 Plot a cumulative size analysis and a size-distribution analysis, and estimate the weights, per 1000 kg of powder, which would lie in the size ranges 0.150 to 0.200 mm and 0.250 to 0.350 mm.
(b)What are the different flow pattern of solids are seen when solids flow out of a bin.
Please do it correctly the three parts I will rate your solution if correct and please by hand
7. A sample of fine aggregate weighs 544 g when SSD and 530 g when OD. The flask weighs 654 g when filled with water and 985 g when filled with fine aggregate and water. Calculate the bulk specific gravity, apparent specific gravity, and absorption.
Table P5.27 shows the grain size distributions of aggregates A, B, and C. The three aggregates must be blended at a ratio of 15:25:60 by weight, respectively. Using a spreadsheet program, determine the grain size distribution of the blend. TABLE P5.27 Percent Passing Sieve Size, mm 25 19 12.5 9.5 4.75 1.18 0.60 0.30 0.15 Aggregate A 100 100 100 77 70 42 34 28 20 Aggregate B 100 85 62 43 24 13 Aggregate C 100 100 84 51 29 19 18 14 9.
Plastics Liquid limit limit 1 1 Can number #7 #8 #9 #10 Mass of empty can (g) Mass of can + soil (wet) (g) 1.7 1.8 1.7 1.7 20.4 23.2 26.3 6.3 Mass of can + soil (dry) (g) 14.7 16.2 17.5 5.3 Number of blows 33 28 23 1. Determine the liquid limit. 2. Determine the plastic limit. 3. Allot group symbols and give soil description by USCS
Draw the free-body diagram of each part of the smooth piston andlink mechanism used to crush recycled cans, shown.