A large home ice cream maker is being used to freeze ice cream. The bowl is at -15C, having just been removed from the freezer. If the bowl is 0.6 m in diameter, the ice cream mix fills the bowl to a depth of 0.55 m, the convective heat transfer coefficient is 220 W/m2 K, and the amount of heat transferred from the ice cream mix to the bowl is 4,300 W, what is the temperature of the ice cream mix?

A large home ice cream maker is being used to freeze ice cream. The bowl is at -15C, having just been removed from the freezer. If the bowl is 0.6 m in diameter, the ice cream mix fills the bowl to a depth of 0.55 m, the convective heat transfer coefficient is 220 W/m2 K, and the amount of heat transferred from the ice cream mix to the bowl is 4,300 W, what is the temperature of the ice cream mix?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

A camper has a propane-powered refrigerator. The refrigerator consumes approximately 0.50 kgof propane per day. When propane is burned completely, it releases approximately 50. MJ/kg.The interior of the refrigerator is maintained at an average temperature of 2.0 °C, and theexterior temperature is 22 °C. Assume that the refrigerator has a surface area of 2.0 m2 and thatthe insulation has an R-value of 3.2 K · m2/W.(a) At what rate does heat flow into the refrigerator?(b) At what rate must the refrigerator remove heat from its interior?(c) How much energy is released per second from the propane combustion?(d) How much heat is delivered to the room?
Calculate the heat transfer rate (in W) through a 4m2 window with h = 2.36 ?/(?2∙℃). The temperature of the cold air outside is −10°C and the temperature of the window glass is 28°C.
50 kg water per minute is to be heated from 30°C to 50°C by passing through a pipe of 2cm diameter. the pipe is heated by condensing the system keeping its inner surface at 100°C . find the length of pipe required. Take the following properties of water at mean bulk temperature of 40°C, density= 965 kg/m^3, v= 0.33*10^-6 m^2/sec , Cp= 4200J/kgK ,k= 0.585W/mK
A refrigerator is connected to a generator powered by a fuel with a calorific value of 35000 kJ/kg and a density of 0.85 g/cm3 . The inside temperature of the refrigerator is 0°C, and the outside temperature is 20°C. a. How much work is required to freeze 500 g of water? ΔfreezingH° = 6.02 kJ mol– 1 ) b. How much internal energy change occurs during the process? c. Since the generator consumes 5 L of fuel per hour, calculate the thermal efficiency of this engine.
A steam compressor is supplied with 110 lbm/h of saturated steam at 0.60 psia and discharges it at 20 psia. and 250°F. The power consumed by the compressor is 3.2 HP. Determine the heat transfer of the steam at BTU/min Answer
1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet bulb temperature at a rate of 14oo cu ft per min. The surface temperature of the coil is 55 F . If 3.5 tons of refrigeration are available, find the dry bulb and wet bulb temperatures of the air leaving the coil. Assume sea level pressure.
Consider a refrigerator that consumes 400 W of electric power when it is running. If the refrigerator runs only one quarter of the time and the unit cost of electricity is P10.50/kWh, the electricity cost of this refrigerator per month (30 days) is
Steam in the condenser of a power plant is to be condensed at a temperature of 30°C with cooling water from a nearby lake, which enters the tubes of the condenser at 14°C and leaves at 22°C. The surface area of the tubes is 45 m2, and the overall heat transfer coefficient is 2100 W/m2K. Determine the mass flow rate of the cooling water needed and the rate of condensation of the steam in the condenser.
A 4-m × 5-m × 6-m room is to be heated by an electric resistance heater placed in a short duct in the room. Initially, the room is at 15°C, and the local atmospheric pressure is 98 kPa. The room is losing heat steadily to the outside at a rate of 150 kJ/min. A 200-W fan circulates the air steadily through the duct and the electric heater at an average mass flow rate of 40 kg/min. The duct can be assumed to be adiabatic, and there is no air leaking in or out of the room. If it takes 25 min for the room air to reach an average temperature of 25°C, find the temperature rise that the air experiences each time it passes through the heater.
A 4-m × 5-m × 6-m room is to be heated by an electric resistance heater placed in a short duct in the room. Initially, the room is at 15°C, and the local atmospheric pressure is 98 kPa. The room is losing heat steadily to the outside at a rate of 150 kJ/min. A 200-W fan circulates the air steadily through the duct and the electric heater at an average mass flow rate of 40 kg/min. The duct can be assumed to be adiabatic, and there is no air leaking in or out of the room. If it takes 25 min for the room air to reach an average temperature of 25°C, find the power rating of the electric heater.
A piston-cylinder device initially contains 1.4 kg of refrigerant-134a at 100 kPa and 20oC. Heatis now transferred to the refrigerant from a source at 150oC, and the piston, which is resting on aset of stops, starts moving when the pressure inside reaches 120 kPa. Heat transfer continuesuntil the temperature reaches 80oC. Assuming the surroundings to be at 25oC and 100 kPa,determine the second-law efficiency of this process.
5. A 4-m x 5-m x 7-m room is heated by the radiator of a steam-heating system. The steam radiator transfers heat at a rate of 10,000 kJ/h, and a 100-W fan is used to distribute the warm air in the room. The rate of heat loss from the room is estimated to be about 5000 kJ/h. If the initial temperature of the room air is 10°C, determine gow long it will take for the air temperature to rise to 20oC. Assume constant specific heats at room temperature where CAIR = 0.768kJ/kg-K. Draw a figure or FBD that will support the problem. Explain each step by step formula.