A link connected between two sits A&B, if the distance between the sites is 60 km andP(Tx) is 2 dB. R(min) is -26 dB, with Attenuation 15 dB and 4 connecters applied along the link,the loss for each connector is 0.6 dB, and the number of a link splicing is 40 points. Explain is thesignal of this link will be arrived as an accepted signal, or no?Consider the splicing loss 0.1 dB and P-margin is 0.1 dB/km.طول الملك

No, the signal will NOT be received as an accepted signal.Here's why:* **Link Parameters:** *…

Answered: A link connected between two sits A&B,…

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Consider two coupled dielectric slab waveguides .The two waveguides are identical to one another and have coupling coefficient:C=C12=C21=500 m-1 a)Find the length of the coupled waveguide structure that allows for complete power transfer from waveguide 1 to waveguide 2.b)Now assume that light is launched into both waveguides at the same power P0 and the same phase,but with linear X polarization in waveguide 1 and linear Y polarization in waveguide 2.Write expressions for the power and the polarization (normalized Jones vector)of the light in each waveguide as a function of the distance traveled.Assume that propagation constants and coupling coefficients are the same for both X and Y polarizations.
The measured output voltage of a cable is 7mv, for an input voltage of 15mv and the near end cross talk ratio (NEXT) of the cable is 20dB. Find attenuation and attenuation to cross talk ratio (ACR) of the cable.
Determine Vo in the scaling circuit has connected two nodes with inverting input, the first node has a voltage source of 3V, and the second node has 2V₁. Assume the feedback resistance equal to 20KN, R₁=5KM, and R₂-2R₁.
Problem 2 In a DSB-SC system, the carrier frequency is 5 kHz and the message signal is given by m(t) 2cos1000nt + sin2000nt. Find and sketch the spectra of the message signal and modulated signal. Identify the upper sideband (USB) and the lower sideband (LSB) spectra in the DSB-SC modulated signal. Determine the average power in the message signal as well as in each frequency component of the modulated signal. Problem 3 The modulating signal m(t) = cos1000nt cos3000nt is multiplied by the carrier c(t) = cos(2nfct), where f. = 5 kHz. Determine and sketch the spectra of the modulating and modulated signals. Identify the upper sideband (USB) and the lower sideband (LSB) spectra in the DSB-SC modulated signal.
A graded index fiber has a core with a parabolic refractive index profile which Q.4 has a diameter of 50 um. The fiber has a numerical aperture of 0.2. Estimate the total number of guided modes propagating in the fiber when it is operating at a wave- length of 1 µm. The numerical input/output mean optical power ratio in one Km length of fiber is found to be 2.5. Calculate the received mean optical power when a mean power of 1 mW is launched into a 5 km length of fiber. Assume no splicing and no connectors being used. Q.5 Q.6 What is the loss in dB per Km of this fiber? An optical signal has lost 85% of its power after traversing 500 meter of fiber?
Design a 4 x 4 multiplier in Verilog HDL using any method of coding
Asap
Q2. A signal travels from point A to point B through a link. It was found that at point B, the signal's power was 65W, whereas, at point A it was 98 W. Explain why there is a difference in the signal strength. What is the difference in the strength between these 2 points in decibels? Show your calculation and explain what does your result state
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 18 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 2 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 600, compute for the primary peak voltage. D1 D2 D3 D4 v(Volts) v2 (seconds)
8. Consider transmitting a digital data: 10111000101. Draw the signal representation when a. Using the Manchester method b. Using the differential Manchester method c. Using the Bipolar method
Question 2 In Figures 2, 3, 4 and 5 the designation of the state of the MISO signal is "Hi-Z" before an. after the SS signal is low. This means the output driving the signal is turned completely off and not driving the signal either high or low. "Hi-Z" means "High Impedance". Also in the figures, the designation of the state of the MOSI signal is "XXX" before and after the SS signal is low. This means the state of the signal is "Unknown" or "Don't Care". If there are multiple Slaves on the bus, why must a Slave turn off the driver (Hi-Z) on the. MISO signal when their SS signal is high
A switched more power converter is designed and open loop transfer function is given by G(s)=(10(1+0.05s))/((1+s)(1+0.5s)(1+0.1s)) Design the frequency response Bode plot |G(jw| and [G(jw}H on log w scale. Also find the Phase margin as well as gain margin.

SEE MORE QUESTIONS

Recommended textbooks for you

Database System Concepts

Computer Science

ISBN:

9780078022159

Author:

Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:

McGraw-Hill Education

Starting Out with Python (4th Edition)

Computer Science

ISBN:

9780134444321

Author:

Tony Gaddis

Publisher:

PEARSON

Digital Fundamentals (11th Edition)

Computer Science

ISBN:

9780132737968

Author:

Thomas L. Floyd

Publisher:

PEARSON

Database System Concepts

Computer Science

ISBN:

9780078022159

Author:

Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:

McGraw-Hill Education

Starting Out with Python (4th Edition)

Computer Science

ISBN:

9780134444321

Author:

Tony Gaddis

Publisher:

PEARSON

Digital Fundamentals (11th Edition)

Computer Science

ISBN:

9780132737968

Author:

Thomas L. Floyd

Publisher:

PEARSON

C How to Program (8th Edition)

Computer Science

ISBN:

9780133976892

Author:

Paul J. Deitel, Harvey Deitel

Publisher:

PEARSON

Database Systems: Design, Implementation, & Manag…

Computer Science

ISBN:

9781337627900

Author:

Carlos Coronel, Steven Morris

Publisher:

Cengage Learning

Programmable Logic Controllers

Computer Science

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

SEE MORE TEXTBOOKS