A load of 6,100 N + 1100 acts on the machine part shown in Fig. 5a. The machine part has a uniform thickness of 15 mm (i.e., 15-mm thickness in the z direction). Determine the normal and shear stresses acting at points H and K, which are shown in detail in Fig. 5b. For each point, show these stresses on a stress element. 10 mm -50 mm 50 mm 40 mm K B Fig. 5a 135 mm D 40° 40 mm Ho 15 mm Fig. 5b 40 m

A load of 6,100 N + 1100 acts on the machine part shown in Fig. 5a. The machine part has a uniform thickness of 15 mm (i.e., 15-mm thickness in the z direction). Determine the normal and shear stresses acting at points H and K, which are shown in detail in Fig. 5b. For each point, show these stresses on a stress element. 10 mm -50 mm 50 mm 40 mm K B Fig. 5a 135 mm D 40° 40 mm Ho 15 mm Fig. 5b 40 m

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

For the state of stress shown in the figure. a. Determine the maximum and minimum principal stresses.b. Describe the location of the maximum principal stress from side BC.c. Describe the location of the maximum principal stress from side BD.d. Determine the maximum shear stress.e. Determine the normal and shear stresses at plane AB. A = 30 ,B = 50 , C = 10 ,D = 37
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
A compound shaft consists of segment (1), which has a diameter of 1.0 in., and segment (2), which has a diameter of 1.3 in. The shaft is subjected to a tensile axial load of P = 16 kips and torques TA = 14 kip·in. and TB = 32 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 14 kips and torques TA = 5 kip-in. and TB = 34 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
Find the stress distribution at section ABCD for the block shown in mm in the following figure, If P=64 kN. For the same section, locate the line of zero stress. Neglect the weight of the block.
The shaft shown in (Figure 1) is supported by bearings at A and B that exert force components only in the x and z directions on the shaft. If the allowable normal stress for the shaft is σ allow = 15 ksi, determine the smallest diameter of the shaft that will support the loading. Use the maximum shear stress theory of failure. Take τ allow = 2.7 ksi.
A very thin rectangular plate (see figure (a)) is subjected to a biaxial plane stress state (σx, σy). The width and height of the plate are b = 7.5 [in] and h = 2.5 [in], respectively. The measures show that the strains in the (x, y) directions are εxx = 2.85x10−4 and εyy = −1.90x10−4, respectively. Figure (b) shows a 2D front view of the plate. a) Draw and identify the principal stresses and the maximum shear stress on Mohr's circle. In what orientation does this maximum shear occur? b) Calculate the unit volume change e = εxx + ?εyy + εzz Note: remember that in a plane stress state we have σz = τxz = τyz = 0 and if it is also bi-axialwe have τyx = 0.
A thin walled tube of thickness (t) 5mm and diameter (d) 200mm with closed ends is subjected to an internal pressure (p) 7.0 MN/m2, producing an axial and circumferential direct stresses given by pd/4t and pd/2t respectively. A torque T = 15.0 kNm is also applied which sets up a shear stress ? = ?/2??2? where r is the radius. (a) Determine the magnitude and direction of the principal stresses. (b) Calculate the overall maximum shear stress.
A hollow shaft shown with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 75 kN and torques TB = 16 kN-m and TC = 7 kN-m. 17. Calculate the absolute value of the minor principal stress at point H in MPa. 18. Calculate the absolute value of the major principal stress at point H in MPa. 19. Calculate the absolute value of the maximum shear stress at point H in MPa. 20. Calculate the orientation of the principal axes in degrees.
Very very Urgent The distributed load q and the singular moment M act on the stepped shaft given in the figure. Draw the cross-sectional influence diagrams of the system under these forces. Determine the maximum stress value for the critical section. L1 = 226 mm ,L2 = 118 mm, a = 159 mm M = 572 N.m, q = 5 N/mm D = 51 mm , d1 = 19mm , d2 = 5 mm
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 23.6 ksi, Sy = 2.8 ksi, and Sxy = 7 ksi. Assume β=19∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.
A square post with a tubular cross section is loaded as shown in the figure below. a) Determine the state of the stress at point A having sides parallel to x and y axes. b) Determine the principal planes and principal stresses at point A at the base of the post.