A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E-73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 12 mm and a length of L₁ - 2.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 22 mm and a length of L₂ - 1.7 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P - 80 KN is applied to the rigid bar. L₁ Answer: 0₁- i 0₂- 164 L2 (1) (1) MPa MPa

A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E-73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 12 mm and a length of L₁ - 2.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 22 mm and a length of L₂ - 1.7 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P - 80 KN is applied to the rigid bar. L₁ Answer: 0₁- i 0₂- 164 L2 (1) (1) MPa MPa

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.4P

See similar textbooks

Similar questions

Two helical springs A and B with ground ends are made of the same material and are in parallel. The wire diameter of the springs A and B are 11 mm and 8 mm, respectively, and the spring indices of A and B, are 6 and 10, respectively. Determine the load supported by spring A in N if the load supported by spring B is 490 N.
A mass of 1019Kg is supported by two wires A and B each made of a different material. Before loading the wires are of equal length. After loading they are still of equal length. Find the load carried by each wire. Wire Diameter mm E Nmm-2 A 1 206,000 B 2 116,000
2. Load-bearing part, as shown in Figure 2.1, find 2.1 Reaction force acting on points A and B 2.2 Then Panyasil recommends to modify the additional section as shown in Figure 2.2 to reduce the reaction force on point B can be reduced. Do students think that Panyasilp's statement is correct (Photo 2.1,2.2 L1=120mm L2=150mm)
2. The structure is connected by a pin joint at point A and by a cable of length L at points B and C, respectively.When load P is given at point D as shown below, what is the vertical displacement at point D?
A steel cable is used to lift a load W with the following given. weight W = 175 kN diameter = 30.03 mm length = 12.02 mm E = 200 GPa 1. Find elongation. 2. Find strain. 3. What is the ductility of material in percentage given that steel cable fails at 27.50 mm diameter. Please make sure your handwriting is readable.
A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB.
The diameter (d) of a solid rod (i.e., with a circular cross-section) is 16 mm and is made from a homogeneous material. The length (L) of the rod is 1.75 m and Young’s Modulus for the material (E) is 250 GPa. When the rod is placed under tension it experiences deformation and a stress (?) of 650 MPa. Calculate the following:(1) Strain energy (U) to 2 decimal places in Joules.(2) Strain energy per unit volume (U/V) in J/m3(3) The change in length ∆L to 2 decimal places in mm.(4) The strain (?) due to deformation to 2 significant figures. (show all work)
The boom has a negligible weight, but has sufficient strength to support the 1000N load. Find the force in the boomBC. Refer to Figure d. a. 1577.50N c. 1154.70N b. 2,000N d. 577.35N
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
! How to compute the strain displacement matrix for each element?
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.