A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 16300 ksi] rods, and a solid steel [E = 30800 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.63 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.49 in. Assume L1=37 in and L2=68 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) %3D

A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 16300 ksi] rods, and a solid steel [E = 30800 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.63 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.49 in. Assume L1=37 in and L2=68 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) %3D

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
FORCE METHOD An overhang beam ABC is loaded as shown. Determine the reactions at the supports due to loading and a support settlement of 1 mm at the roller B. Take E = 200 GPa and I = 500(10^6) mm^4.
A simply supported beam AB = 11 m has a hollow rectangular cross-section with 19 cm as width, 20 cm as depth, and inner thickness as 1 cm is subjected to a point load of 8 N & 7 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 2 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
The pillar is a cylinder that has a diameter of 68 mm , modulus of elasticity of E = 200 GPa . It is is fixed at A and B. The support at A is concrete and therefore rigid. The support at B can be considered rigid only if the reaction force at B does not exceed 110 kN . The lengths are LAB = 6.4 m and LAC = 3 m . 1)What is the maximum load, P, that can be applied such that the reaction at B does not exceed 110 kN ? 2)What is the reaction force at support A?
The inclined beam shown is supported by a pin at the left end and a roller at the right end. The rise:run of the beam is h/L=5ft:15ft, what is the actual (sloping) length of the beam? PART A. A vertical point load of P=48 kips is applied at the midspan of the beam. Raplace the point load vector P with its two vector components oriented parallel to the beam (Pa) and paerpendicular to the beam (Pb). State the magnitudes of Pa and Pb. PART B. A vertical distributed load of w=3.2 kip/ft is applied along the length of the beam. Replace the distributed load vector (w) with its two vector components oriented parallel to the beam (wa) and perpendicular to the beam (Wb). What are the magnitudes of Wa and Wb?
.The beam is subjected to the loads q0 and P, with the values added to the table below. Point C, where force P is applied, is located at L/2 from points A and B. Knowing, that cross section of the beam has moment on inertia equal to 232*106 mm4. The beam was modified to improve its performance and structural integrity roller support was placed at point B. For the system determine: a) Reaction forces using integration method b) Reaction forces using method of superposition;
Use Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. a=4.5 b=26 c=10 Determine: Vertical Reaction at C in kN. Moment Reaction at C in kN-m.
For the beam and loading shown below, determine the reactions at supports A and B. Assume that EI = 8.6× 106 kip·in.2 is constant for the beam. Use w = 11 kips/ft and L = 12 ft. Remove support C and use the appropriate equations from Appendix C to calculate the deflection at point C caused by the distributed load. Use the sign convention from the textbook (deflection is positive upward).
Using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. a=4.5 b=26 c=10 Determine: Vertical Reaction at C in kN. Moment Reaction at C in kN-m.
A tripod shown supports a load of P = 1000 N at point A. Take note that ball and socket joints are used to mount the triopd at points B, D, and C. Consider the following:L1 = 2L2 = 4L3 = 5θ = 45°α = 30 Point C coordinates: (2, -2, 3) Determine the following: Force of AB = __NForce of AC = __NForce of AD = __N
A simply supported beam AB = 9 m has a hollow rectangular cross-section with 13 cm as width, 20 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 8 N acting at C and D respectively and a uniformly distributed load (UDL) of 9 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 2 m. note; sole 4 . 5.6 and 7 i) Reaction force at B in (N)= ii) Reaction Force at A in(N)= iii) The distance from B at which the shear Force value changes from "-" to "+" in (m)= iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I in (m^4)= vi) Maximum bending stress in (N/m^2)= vii) Bending stress at 1 cm from the top in (N/m^2) =
Rigid bar ABCD is pinned at C and supported by bars (1) and (2) at A and D, respectively. Bar (1) is aluminum and bar (2) is bronze. A concentrated load P = 80 kN is applied to the rigid bar at B. Compute the normal stress in each bar and the downward deflection of the rigid bar at A.