A loaded cable can be seen in the figure below. If the sag of the cable is 1m and W = 50 KN, A. Find the distance x1 such that the tension in AB is equal to that in BC. B. If x1 = 5m, determine the tension in BC. C. Calculate the total length of the cable if x1 = 5m. H A X1 B W 20 m X2

A loaded cable can be seen in the figure below. If the sag of the cable is 1m and W = 50 KN, A. Find the distance x1 such that the tension in AB is equal to that in BC. B. If x1 = 5m, determine the tension in BC. C. Calculate the total length of the cable if x1 = 5m. H A X1 B W 20 m X2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the ASD design strength (kN) of the compression member shown. The distance between the…

A: Given, L = 5.9 m or 5900 mm Fy = 345 MPa W310 x 67

Q: For the beam shown, calculate the following if the unit load is composed of a concentrated load P =…

A: Given data in question Load = 120 kN WLL = 20KN/m WDL = 30 kN/m Span member length 5 m To find out…

Q: A square bar carries the series of loads as shown. Compute the load (kN) and stress (MPa) in each…

Q: A rectangular beam has b = 310 mm and d = 460 mm. The beam will be designed to carry a service dead…

Q: Q-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a…

Q: A concrete channel with trapezium cross-sectional shape, conveys water at 40 m³/s. The base width of…

A: Q = 40m3/sec width = 4m side slope = 1:1 longitudinal slope = 16/10000 N = 0.017 It has been asked…

Q: Given the following properties of T-beams. If the beam is reinforced in tension only, determine (a)…

Q: A w B

A: Given : P = 13 Kn w = 10 kN/m To Find :

Q: B LA "' 11 1 il 11 il || U B N Fig. 5-5-L Matching test. R 13 NO DE 17 21 S W AL 14 CASA 18 8 HA n…

A: To Match the Orthographic projections with the isometric ones

Q: The load distribution between the front and the rear axle of a motor vehicle weighing 1350 kg is…

A: The front axle conveys the heaviness of the front piece of the auto as well as works with directing…

Q: ACTIVITY (NODES) IMMEDIATE DURATION (DAYS) A 25 B 15 A 20 D. В 20 E В 31 A 17 43 D, E 55 A 25 H 10 K…

A: Earliest start time (EST) - it is the earliest time by which an activity can start. Earliest finish…

Q: A hollow circular shaft of inner radius 10 mm, outer radius 20 mm and length 1 m is to be used as a…

Q: A reservoir with a live storage of 300 million cubic metre irrigate 40000 hectares (1 hecatre = 104…

A: Given data Reservoir live storage (S) = 300 Mm3 Area (A) = 40000 hectares Base period (B) = 120…

Q: SITUATION IX: A projectile is fired with a velocity of 300 m/s at an angle of 20° with the…

Q: er a simply supported beam of length / subjected to a 1/ y(x) = P x ≤ 1/2, the deflection is given…

Q: The soil layer of depth 3m and unit weight in submerged condition in water level of 5m is 21kN/m³.…

A: GIVEN :- Depth of soil layer = 3 m Unit weight of soil = 21 kN/m3 Level of water = 5m To Determine…

Q: A boy tied an 80 grams stone to a string which he rotated to form a circular motion with a diameter…

Q: Water is pumped from the large tank shown in the figure below. The head loss is known to be equal to…

A: Given data:- The given value of the head loss, hL=3V22g hp=18-5Q2 The given area is, A=0.09 ft2 The…

Q: A BY RANN OG NAGE AGEN 6 m 4 kN/m C 4.5 m B *Assume A to be rocker, B to be fixed support, and C to…

Q: 6. Classify the foloowing soils according to the AASHTO classification system and give the group…

Q: 오 A 3m SOKN ↓ 3m B J Hinge 10KN/M qm - ㅇㄹ C

Q: This figure shows a cantilever beam that is subject to a point load and a moment. What is the…

A: Given data in question Load 60 KN Moment 300 kNm Span member length 10 m Elasticity modulus 200 GPa…

Q: PLATE #3 PROBLEM: A built up section of A992 steel is made from plates fully welded together. The…

Q: The soil layer of depth 3m and unit weight in submerged condition in water level of 5m is 21kN/m³.…

Q: For the frame shown, calculate the following: 4. The moment at D. 5. The moment at B 6. Horizontal…

Q: Design

Q: 2. Given H = 1.8 m & D = 0.2 m through the hole in the open top container. Determine the head losses…

Q: n isosceles triangular lot has an area of 12,640 square feet. The included angle between the two…

A: Median drawn from a vertex divides the opposite sides in two equal parts. Two angles of an isosceles…

Q: -2 A 15 kN 10 kN 2 m -2 m B 6 m 45% C 4 kN/m

Q: 3. The moist unit weight and degree of saturation of a soil are given in the following table: Degree…

A: To Determine :- Void ratio, e and specific gravity (G) of the soil.

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

Q: Q2: Water flows in a rectangular channel with a flow rate 5m³/s, and figure (1) shows the specific…

Q: 5. A metric M4 x 15 square key is used with a 16 mm shaft. If the allowable shearing stress is 50 Mp…

A: Diameter of shaft(d)=16mm w=4 l=15 Shear stress=50MPa

Q: 3. What is the total length of the course XY if the rear tape-man holds exactly holds 9 pebbles and…

A: Using formula

Q: lon concentrations obtained for a ground water sample (having pH = 8.1) are given below Ion Ca²+…

A: To Determine :- Carbonate hardness present in the given water sample.

Q: Angle: 34.9 Start point x: -9.7 y: -6.2 End point x: -3.1 y: -1.6

Q: The scale on the map is 1: x. A lot having an area of 640 sq.m. is by an area of 25.6 cm² on the…

A: Solution is attached below

Q: The box at B weighs 50-lb. Assume that there is enough friction to prevent slip at B. The plank…

A: Given : Weight of box at B = 50 lb Plank weight = 25 lb Determine the tension in the rope and…

Q: The box at B weighs 50-lb. Assume that there is enough friction to prevent slip at B. The plank…

Q: Calculate the moment of inertia of the following object. Note the circular hole is cut out and has a…

A: Given : To Find : Calculate the moment of inertia ?

Q: (Situation 1) Consider the following beam: X y max W B (a) Determine the support reactions at A and…

Q: 2 kN/m 6 kN/m B 6 kN/m 2.5 m 4 m -6 m -6 m *Assume A and C to be pinned support, and B to be a…

Q: An open-ended steel barrel of 1 m height and 1 m diameter is filled with saturated fine sand having…

A: Given- Height h=1 m, Diameter d=1 m, permeability k=10-2 m/s.

Q: An HSS 10 x 6 x ¾/16 with F, = 46 ksi is used as a column. The length is 15 feet. Both ends are…

A: Reference : Structural design, Steel design and structural design manual. Given : HSS 10 X 6 X 5/16…

Q: The velocity of water at the outer edge of a 60cm diameter whirlpool, where the water level is…

Q: PROBLEM 1 A uniform rod PQ of mass 12kg and length 8m rests horizontally in equilibrium, supported…

Q: Determine the moment at B for the beam shown.

A: ###DETERMINATION OF MOMENT AT B USING 3 MOMENT EQUATION METHOD ####

Q: locate a missing point on the ground: a. You need at least three reference points b. You need at…

A: Given To locate a missing point on the ground:

Q: 3. What is the total length of the course XY if the rear tape-man holds exactly holds 9 pebbles and…

Q: 5.27 (Ans. max V = 29.6 k, max M = 109.5 ft-k) 4 klf 10 ft 15 ft 30 k 10 ft 30 k 1 ft #1 ft

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Need right complete solution and box the answer

A loaded cable can be seen in the figure
below. If the sag of the cable is 1m and W =
50 KN,
A. Find the distance x1 such that the tension
in AB is equal to that in BC.
B. If x1 = 5m, determine the tension in BC.
C. Calculate the total length of the cable if x1
= 5m.
H
A
X1
B
W
20 m
X2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cable in Figure P6.2 supports four sim-ply supported girders uniformly loaded with 6 kips/ft.(a) Determine the minimum required area of the maincable ABCDE if the allowable stress is 60 kips/in.2.(b) Determine the cable sag at point B.
A cable ABCD is pulled at end E by a force P (Figure P6.12). The cable is supported at point D by a rigid member DF. Compute the force P that produces a sag of 2 m at points B and C. The horizontal reaction at support F is zero. Compute the vertical reaction at F.
A uniform cable weighing 15N/m is suspended from points A and B. The force in the cable at B is known to be 500N. Using the result of Prob. 6.69 , calculate (a) the force in the cable at A; and (b) the span L.
Determine the tension P in the cable which will give the 100 lb-block a steady acceleration of 5 ft/sec^2 up the incline.
The cable supports the loading shown. Determine thedistance y and the tension in cable BC. Set P = 3 kN.
If the tension on the cable AB is 5kips, determine its component parallel and normal the plane ABC.
For the cable shown below,Determine the tension segment CD in kNDetermine the tension segment AB in kNWhat is the value of h?
A cable supports 100-KN load at point B and 80-KN load at point C as shown in the figure. Determine yB and the tensions in segments AB, BC and CD of the cable.
Auniform cable weighing 15N/m is suspended from points A and B. The force in the cable at B is known to be 500N. Using the result of Prob. 6.69, calculate (a) the force in the cable at A; and (b) the span L.
Determine the force P needed to hold the cable in the position shown, i.e., so segment BC remains horizontal. Also, compute the sag yB and the maximumtension in the cable.
Two cables are tied together as C and loaded as shown. Consider P = 395 N and Q = 480 . Find the tensions in cable AB and BC
Compute the support reactions and the macimum value of w if the allowable tension force in the cable shown is 200 kN.