A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown in Fig. When the water level reaches 15 ft, the cylindrical gate opens by turning about the hinge at point A. Determine the hydrostatic force acting on the cylinder (Answer 1747 Ibf) I5 A 21

A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown in Fig. When the water level reaches 15 ft, the cylindrical gate opens by turning about the hinge at point A. Determine the hydrostatic force acting on the cylinder (Answer 1747 Ibf) I5 A 21

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Related questions

Q: The figure shown below (Fig. 1) is a schematic representation of a conversion system linear-rotation...

Q: Calculate the x and y components of a 30m displacement at 23° from the x-axis

A: Given data : Displacement (d)=30 m θ=230 from the X axis.

Q: A gas is stored in a cylindrical tank of inner radius 7 m and wall thickness 50 mm. The gage pressur...

A: Given, Radius of cylinder = R = 7 m = 7000 mm Wall thickness = t = 50 mm Gage pressure of the gas = ...

Q: o raise and lower the 580-kg bucket i uired to slow the descent of the buch ble.

Q: If the bucket and its content have a mass of 10 kg and are suspended from the cable by means of a sm...

Q: Polar moment of inertia (I,), in cm, of a rectangular section having width, b 2 cm and depth d= 6 cm...

A: Given data : Width of rectangular section=b b=2 cm Depth of rectangular section=d d=6 cm

Q: 3. A 5m long x Im wide horizontal plate is heated on top and insulated on the bottom. The plate is m...

Q: The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to a dept...

A: Tanθ = ag=33=1 V = u + at 10 = 0 + 3(t) t = 10 / 3 = 3.33

Q: Which invariant reaction can be recognized in the phase diagram shown here? 2500 2300 2100 1900 1700...

A: The correct option in peritectic (option D). The copper-iridium phase diagram is an example of simpl...

Q: (3) A steel bar and an aluminum bar are bonded together to form a composite beam shown. The modulus ...

Q: Pressure remains constant at 689.5 kPa while the volume changes from 0.567 m3 to 0.283 m3. Find the ...

Q: 2. At the beginning of the compression stroke and ideal Otto cycle has an air pressure of 15 psia, a...

A: Dear student, According to the guidelines I am allowed to answer only three sub-p...

Q: ockets are fired one after the other at 1.2-sec intervals, and the duration of each rocket firing is...

Q: QUESTION 5 Knowing that the tension in cable AC is 1065 N, determine the moment about each of the co...

Q: The equation of motion for the system shown in figure is WA k m Fecosat

Q: Find the transfer function C(s)/R(s) for t reduction:

A: To find the transfer function.

Q: 4. A dancer is standing on her toes of one foot during her routine, as shown, Determine the force in...

Q: Encontrar la tensión o compresión de cada varilla si el peso que tiene que soportar es de P=10KN 2 V...

A: tanθ=31/2/1 θ=60° Calculating reactions at A and D, sum of horizontal forces along X direction = 0 H...

Q: Find the resultant force of these forces 240 N. 204 N 400 N 21 30 360 N 30

A: Given Data :

Q: Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate o...

A: Given Data Weight W = 70 Kg Spring rate for spring 1= 0.209 Kg/mm Spring rate for spring 2 and 3=...

Q: The rigid beam of negligible weight is supported by a pin at o and two vertical rods. Find the verti...

Q: All four compression coil springs supports a load of 400 kg. The springs are arranged in parallel an...

A: Given Data K= 0.709 kg ∕mm F=400 kg

Q: Find the centre of gravity of an inverted T-section with flange 60 mm × 10 mm and web 50 mm × 10 mm...

A: Given data as per question flange dimensions =60 mm × 10 mm web dimensions =50 mm × 10 mm. conside...

Q: Q1. A spur gear train with a speed reduction of 3:1 is to be used in a sugarcane crusher. A single c...

A: ear ratio = G= 3 speed of pinion = Np= 720 rpm speed of gear= Ng= 720/3 = 240 rpm Power = P= (Q+5)= ...

Q: A sharp edged orifice will be required to produce a discharge of 35 liters/sec of water under a head...

Q: Calculate the value of R shown in Figure 1

A: Need to find the value of R.

Q: Example of 2nd law thermodynamics but not ice cube or coffee or candle. Another example that you see...

Q: For sink temperature of 450 K, efficiency of Carnot engine is 30%. If sink temperature is reduced by...

Q: Dari gambar di atas gambarlah diagram bebas untuk semua batang. Kemudian carilah gaya reaksi tumpuan...

A: Given data Given foce system.

Q: 1. Determine the internal normal force, shear force, and bending moment at point C in the beam. 300 ...

Q: For a damped single degree of freedom system with natural frequency wn and damping ratio § , what is...

Q: Q5/ Replace the two forces by an equivalent resultant force and couple moment at point 0. Set F = 20...

Q: A horizontal bar, fixed at one end (x = 0), has a length of 1 m, and cross-sectional area of 100 mm2...

A: As per given P=10kn L=1m A=100 mm2 We have to determine modulus of elasticity varies along the leng...

Q: m and volume 0.14 m. It is then e temperature remains constant (0.028 m and a temperature of 15 "C. ...

A: Hi and thank you for the questions. Since you have asked multiple questions, we will solve the first...

Q: in compression, determine the factor of safety against failure:

Q: Q4) Determine pin reaction at A & Cas shown in (Fig.)? 2 kN 60

Q: 1. A water from Agno River is pumped at 13.3 L/s using a submerged pump at an efficiency of 78% that...

A: Given: The flow rate, Q = 13.3 L/s = 0.0133 m^3/s The efficiency of pump, η = 0.75 The height of sur...

Q: f 9 m3 of an ideal gas at 24 °C and 150 kPaa is compressed to 2 m3 , (a) what is the resulting pres...

A: Given:V1=9 m3T1=24°C =297 KP1=150 KPaV2=2 m3

Q: Truss detail Member=9 Joint36 Reaction=4 Is truss formed is stable

Q: 2. A symmetric spacecraft is separated from a Delta II launch vehicle which is spinning at 30 RPM. I...

A: according to the given details

Q: Two gaseous streams containing the same fluid enter a mixing chamber and leave as a single stream. F...

A: Given inlet conditions:A1=500 cm2=500×10-4m2V1=130msρ1=1.6Kgm3Mass flow rate at inlet,m1=ρ1A1V1⇒m1=1...

Q: A rod and two balloons A very thin glass rod 4 meters long rubbed all over with a silk cloth. It gai...

Q: 3 2 ll M2 HE Mi skga bF friction less surfau

Q: d that it gave a pressure ratio of 3 atmosphere and temperature rise of 125° C. A 2000 kw motor was ...

Q: Find the magnitude of force if a body of 12 kg is accelerated by 5 m/s2 due to that force.

A: Given, Mass of the body = m = 12 kg Acceleration induced by the force = a = 5 m/s2 As per Newton's...

Q: A one mm diameter steel wire is wounded around a copper tube with external and internal diameters of...

A: Given: The diameter of wore, d = 1 mm The external diameter of tube, Do = 140 mm The internal diamet...

Q: 17/ The fertilizer spreader and the fertilizer it contains have a combined mass of 40 kg and a cente...

A: Givenm=140kgC=5mm

Q: shear center and elastic center.

A: SHEAR CENTRE Shear center is a point on the beam-section where the application o...

Q: Two vessels of different shape and sizes are connected by means of a pipe with a valve. Vessel A has...

Q: 1 2. 8. 09 Draw the isometric perspective of the part whose FRONT and TOP views are given below. (sc...

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
A long solid cylinder of radius 0.8 m hinged at point A is used as an automatic gate, When the water level reaches 5 m, the gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens and (b) the weight of the cylinder per m length of the cylinder.
A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown in the figure below. When the water level reaches 15 ft, the cylindrical gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens. (b) the weight of the cylinder per ft length of the cylinder.
A long, solid cylinder of radius 2 ?? hinged at point ? is used as an automatic gate, as shown in the following figure. When the water level reaches 15 ??, the cylindrical gate opens by turning about the hinge at point A. Determine the hydrostatic force acting on the cylinder and its line of action when the gate opens
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.
An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its minor axis lies in the surface of the water (weight density =p Ib/fr3). Determine the appropriate integral to be used to determine the force on one side of the submerged
A gate which is hinged at O with a constant width of 5m and water depth of 4m to the right of the gate.determine the magnitude of hydrostatic force required to maintain the gate in equilibrium
Calculate the depth of the center of pressure for vertical rectangular plate having a height h = 10ft and base b = 5ft, and submerged in a liquid with its base at the liquid surface. If the upper base of the vertical rectangular plate given in the example problem is submerged by 12ft below the water surface, determine the location of the hydrostatic force and center of pressure. Answer should be (53,040 lbf and 17.4902ft)
A cylindrical tank 2m diameter and 4 m long, with its axis horizontal, is half filled with water and half filled with oil of density 880 kg/m3. Determine the location of the hydrostatic force from the top of the cylinder. Express your answer in two decimal place and in terms of m.
How can I get the solutions for this problem? (answers are given) If the upper base of the vertical rectangular plate with ( height =10ft and base= 5ft) is submerged 12ft below the water's surface, determine the hydrostatic force and the location of the center of pressure. (Answers: 53040 lbf and 17.4902 ft)
1. A rectangular plane surface is 2m wide and 3m deep. It lies in vertical plane in water. Determine the total pressure and position of centre of pressure on the plane surface when its upper edge is horizontal (a)coincides with water surface and (b) 2.5m below the free water surface.
A 3-m-high, 5-m-wide rectangular gate is hinged at the top edge at A and is restrained by a fixed ridge at B. Determine the hydrostatic force exerted on the gate by the 2-m-high water and the location of the pressure center.