A low-pass filter with a passband gain of 5 dB and a cutoff frequency of 10 kHz is shown in (Figure 1). Figure Vi R₁ www C H6 ●+ R₂ www ● 1 of 1 > + Vo Part A If the capacitor has a capacitance of 30 nF, what are R₁ and R₂? Express your answers in ohms to three significant figures separated by a comma. R₁, R₂ = Submit Provide Feedback 195] ΑΣΦ. 11 vec Request Answer ? Ω

A low-pass filter with a passband gain of 5 dB and a cutoff frequency of 10 kHz is shown in (Figure 1). Figure Vi R₁ www C H6 ●+ R₂ www ● 1 of 1 > + Vo Part A If the capacitor has a capacitance of 30 nF, what are R₁ and R₂? Express your answers in ohms to three significant figures separated by a comma. R₁, R₂ = Submit Provide Feedback 195] ΑΣΦ. 11 vec Request Answer ? Ω

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a filter that will pass the two signals x1(t) = 3 cos(2000t + Ti/4) and x2(t) = 2 sin(4000t) and will block the two disturbance signals: xa1(t) = sin(100t) and xa2(t) = 2 cos(10,000t + t/3). 1. By hand show all calculations, find the system transfer function, and draw the circuit diagram 2. Use MATLAB to simulate the filter. Draw the combination of the four input signals. Use the transfer function found in part 1, and find the filter output. Then, draw the Bode diagram
Design a series RLC bandpass filter (see 14.19[a]) with aquality of 2 and a center frequency of 8 kHz, using a 5 nF capacitor.1. a) Draw your circuit, labeling the component values and outputvoltage.2. b) For the filter in part (a), calculate the bandwidth and the valuesof the two cutoff frequencies.
Design a bandpass filter with cutoff frequencies 20k Hz and 80k Hz, with ?=8. (a) Draw your circuit, labeling the component values and the output voltage.(b) 8.4k Ω.(c) What is the central frequency?
Hi, for this question, can I use 1 1st order LPF and 1 1st order HPF in cascade to design the filter circuit? If so, how would I solve this question. Thank you.
Write a program to design a bandpass analog Butterworth that pass the frequency 20 rad/sec for the signal x(t) = sin(20t) + sin(40t) . then 1- Plot the filtered signal (time domain and spectrum). 2- Plot the frequency response of the filter. 3- Verify your result
Show that the series RL circuit also acts like a high-pass filter: 1. Derive an expression for the circuit’s transfer function.2. Use the result from (a) to determine an equation for the cutoff frequencyin the series RL circuit.3. Choose values for R and L that will yield a high-pass filter with a cutofffrequency of 15 kHz.
for the following high pass filter. a. find the transfer function b. Sketch the magnitude Bode plot of the filter. c. If Ri=7 kΩ and C=0.1 µF, design a filter that passes signals with frequencies greater than 3 kHz and has a forward current gain of 13 dB.
The resistor as shown represents the midrange speaker in a three-speaker system. Assume its resistance to be constant at 8.00 Ω. The source represents an audio amplifier producing signals of uniform amplitude ΔVmax = 10.0 V at all audio frequencies. The inductor and capacitor are to function as a band-pass filter with ΔVout/ΔVin = 1/2 at 200 Hz and at 4.00 × 103 Hz. Determine the required values of (a) L and (b) C. Find (c) the maximum value of the ratio ΔVout/ΔVin; (d) the frequency f0 at which the ratio has its maximum value; (e) the phase shift between Δυin and Δυoutat 200 Hz, at f0, and at 4.00 × 103 Hz; and (f) the average power transferred to the speaker at 200 Hz, at f0, and at 4.00 × 103 Hz. (g) Recognizing that the diagram represents an RLC circuit driven by an AC source, find its quality factor.
Design a passive RC low pass filter (14.7) with a cutoff frequency of 100 Hz using a 4.7 μF capacitor. 1. a) What is the cutoff frequency in rad/s? 2. b) What is the value of the resistor? 3. c) Draw your circuit, labeling the component values and output voltage. 4. d) What is the transfer function of the filter in part (c)? 5. e) If the filter in part (c) is loaded with a resistor whose value is the same as the resistor part (b), what is the transfer function of this loaded filter? 6. f) What is the cutoff frequency of the loaded filter from part (e)? 7. g) What is the gain in the pass band of the loaded filter from part (e)?
Design an RLC bandreject filter with a qualityof 5 and a center frequency of 20 krad/s, using a 50 nF capacitor.1. a) Draw your circuit, labeling the component values and outputvoltage.2. b) For the filter in part (a), calculate the bandwidth and the valuesof the two cutoff frequencies.
A resistor, denoted as Rl, is added in series with the inductor in the circuit . The new low-pass filter circuit is shown. 1. a) Derive the expression for H(s) where H(s)=Vo/Vi. 2. b) At what frequency will the magnitude of H(jω) be maximum? 3. c) What is the maximum value of the magnitude of H(jω)? 4. d) At what frequency will the magnitude of H(jω) equal its maximum value divided by 2? 5. e) Assume a resistance of 75 Ω is added in series with the 10 mH inductor in the circuit. Find ωc, H(j0), H(jωc), H(j0.2ωc), and H(j5ωc).
As part of a radio receiver, you are asked to design a simple bandpass filter using a series inductor, capacitor and resistor. The filter needs to pass a centre frequency of f0 = 1089 kHz with a bandwidth of 9 kHz. Do this by finding the capacitor and resistor values together with a 240 uH inductor that will give you the correct centre frequency and bandwidth. Also, calculate the quality factor Q for your filter. Sketch the filter circuit and show all your calculations.