:A modulating signal is used to modulate a carrier signal(AM modulation). Let Pr , Pc, PSB, PUSB, PLSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively. Prove the following: m2 a. Pc = Pr (me) m2 b. PSB = PT PLSB =7 2+m2, c. PUSB = PT 2+m2

:A modulating signal is used to modulate a carrier signal(AM modulation). Let Pr , Pc, PSB, PUSB, PLSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively. Prove the following: m2 a. Pc = Pr (me) m2 b. PSB = PT PLSB =7 2+m2, c. PUSB = PT 2+m2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In AM modulation, the equation of the modulating signal is given by f(t) = Am cos ωm t. If the amplitude of the carrier wave is A and there is no over–modulation, then what will be the modulation efficiency?
Problem1: the figure shows multiple modulation schemes for the signal that is given by the dashed line sinusoidal function, the X-axis is the time axis is seconds and the Y-axis is the amplitude. Answer the following: 1. What is the value of the duty cycle in A? 2.What is the quantization noise in a modulator that uses a 4-bits register for the analog to digital conversion of the given sinusoidal signal?
- An AM signal has a carrier of 10MHz and modulating signal of 10kHz. It has a modulation index of 0.7. Write its expression an calculate power efficiency?
a) For amplitude modulation (AM)i) Write the time domain equation for AM signal XAM(t).ii) Write the frequency domain equation for AM signal XAM(ω).iii) Draw the circuit diagram for the envelop detector.iv) Define the modulation index and its maximum value. b) An audio signal 3sin 2π(4000t) amplitude modulates a carrier 5sin 2π(500000t).i) Sketch the amplitude modulated wave.ii) Determine the modulation index ?iii) What is the frequency content of the modulated wave? c) An audio signal 10sin 2π(2000t) amplitude modulates a carrier 20sin 2π(200000t).i) Sketch the amplitude modulated wave.ii) Determine the modulation index?iii) What is the frequency content of the modulated wave? d) How many AM broadcast stations can be accommodated in a 100 KHz bandwidth if the highest frequency modulating a carrier fmax is 5 KHz? e) The total power content of an AM signal is 1000 W. Determine the carrier power PC and the sideband power Ps and power efficiency when the modulation index is 0.5? f) An…
In Amplitude modulation, Vestigal Side Band (VSB) is one of the technique used to overcome its limitations in terms of power and bandwidth. With this in mind; a. Explain how a VSB signal is generated in the transmitter. b. Draw and compare the frequency spectrum of the original message signal and the spectrum of the VSB signal in a frequency domain. c. Show how the bandwidth of VSB is calculated by writing the equation. d. Give one application of VSB in broadcasting.
A 450 kHz carrier signal is modulated with a 15 kHz modulating signal. What are its sideband frequencies?
If the amplitude of the modulation signal voltage was given to be -4v and +4v and carrier amplitude also given to be -22v and +22v, by suitable waveform diagram determine the Am modulated output. Remember to provide all necessary wave forms in practical terms.
A 1500 KHz carrier with amplitude of 50 V is amplitude modulated by 2 –KHz sine wave tone with a peak voltage of 15 V. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 750 kHz is amplitude-modulated by a 4 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 180Vp and 70Vp respectively. The equivalent resistance of the transmitting antenna is 60 Ω. Determine: (i) The peak amplitudes of the audio, carrier sideband voltages and modulation index. (ii) Using the above results, write the complete AM mathematical representation to express the waveform, showing its carrier, lower sideband and upper sideband parameters. (iii) The power of the carrier signal, total sidebands power and the bandwidth of the modulated signal. Then sketch and label the power spectrum of the modulated ( i v ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC
For an AM, DSBFC modulator with a carrier frequency fc=801KHz and a maximum modulating signal frequency fm=9KHz, determine: a. Frequency limits for upper and lower side band b. Bandwidth c. Draw the output frequency spectrum c. d. State two advantages and two disadvantages of FM over AM.
pls list the step by handwritinga) Sketch the spectrum of g(t)?b) Sketch the spectrum at point (a) of the conversion system?c) What should the parameter w0 be relative to wc?d) What should be the value of passband gain A?
q16)This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer. A baseband system has a signal-to-noise ratio of 23 dB and a bandwidth to bit rate ratio of 0.4 .The average bit energy to noise spectral density of this system is equal to------- a)none of the mentioned b)125 c)250 d)80