A new 144 MW hydropower station is to be built at a site where the available head is estimated at 270 m. The generators require the turbine to rotate at 10 rad/sec. The only available turbines are Francis turbines with KN (the non-dimensional parameter to classify turbine ) equal to 0.08. Determine the number of turbines required.

A new 144 MW hydropower station is to be built at a site where the available head is estimated at 270 m. The generators require the turbine to rotate at 10 rad/sec. The only available turbines are Francis turbines with KN (the non-dimensional parameter to classify turbine ) equal to 0.08. Determine the number of turbines required.

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter13: Tidal Energy

Section: Chapter Questions

Problem 12P

See similar textbooks

Similar questions

A hydroelectric power station is supplied from a reservoir having an area of 50 km2and a head of 50 m.If overall efficiency of the plant is 60%, find the rate at which the water level will fall when the stationis generating 30,000 kW
Water is pumped at a flow rate of 15 m3/s from the lower reservoir through a pipe with a diameter of 1.50 m. How much power does the water need to be powered to produce this much flow?
A hydroelectric power generating system is shown in the figure. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 187 liters per second. The total length of pipe connecting the two reservoirs is 143 m. The pipe diameter is 376 mm and the Hazen-Williams coefficient is 143. The water surface elevations of reservoirs 1 and 2 are 210 m and 68 m, respectively. Determine the power in kW required by the turbine if it is 79% efficient? Neglect minor losses. round your answers in 3 decimal places
Design head at China’s Three Gorges Dam, the largest hydropower project in the world, is 80.6 m, and rated power output of each of the 32 turbine generator units is 700 MW. If the efficiency of each of the turbine generator units at full power output is 93.2%, what is the design flow through each turbine?
Water is pumped 14.5 km from a reservoir at elevation 30 m to another reservoirat elevation 70 m. The steel pipeline connecting the reservoirs has a nominal diameter of 1400mm (the actual inside diameter is 1372 mm) with C = 90. If the flow is 1.18 m3/s, the pumpingefficiency is 82%, and electricity costs $0.14/kWh. Assuming that the density of water is 1000kg/m3, what will be the monthly power bill? Sketch the hydraulic and energy grade lines.
5. Water is pumped 14.5 km from a reservoir at elevation 30 m to another reservoir at elevation 70 m. The steel pipeline connecting the reservoirs has a nominal diameter of 1400 mm (the actual inside diameter is 1372 mm) with C = 90. If the flow is 1.18 m3/s, the pumping efficiency is 82%, and electricity costs $0.14/kWh. Assuming that the density of water is 1000 kg/m3, what will be the monthly power bill? Sketch the hydraulic and energy grade lines.
During a prefeasibility survey, you have identified a feasible site for a micro hydropower scheme. If you’ve measured a gross head of 40 m, and from the hydrological analysis, a design flow of 150 l/s appears to be available throughout the year, what would be the likely installed capacity? Assume an overall efficiency of 60%.
Water flows through a 7.5 m diameter penstock on a dam at a flow rate of 113 m3/s. The total head available for the turbine is 18.4 m. The specifiic weight of water is 9810 N/m3. What is the power generated by the turbine?
Determine the total energy production of a run-of-river plant having an total efficiency of 85%. It receives flow by means of a penstock, 400m long with 1.2m diameter, and f=0.015 in Darcy-Weisbach equation. The available head is 200m and seasonal fluctuations of upstream and downstream water levels are ignored. The flow duration data are tabulated as below.
2.1 A hydro-electric power station has a reservoir area of 2.7 km² and a capacity of 4.6 x 106m³. The effective head of water is 100 metres. The penstock, turbine and generation efficiencies are 95%, 90%, and 85%, respectively. Instructions :round off to 2 decimal places 1. Determine the total electrical energy that can be generated from the power station (kWh). 2. Determine the depth of the reservoir (metres) 3.Determine the fall in reservoir volume level is the load of 100 kW is supplied for 5 hours (%).
The flow of a river is 150 cubic feet per second at a site where a 75 feet hydrostatic head canbe created by the erection of a dam. What is the potential capacity (in kW) of a hydroelectricpower plant if installed at this site? Consider that hydraulic efficiency of energy conversioncan be 80%, and that the electric efficiency can be 90%.
At a proposed hydroelectric power plant site, the average elevation of headwater is 600m and the tailwater elevation is 480m. The average annual water flow is determined to be equal to that volume flowing through a rectangular channel 4m wide and 0.5m deep and average velocity of 5.5m/s. Assuming the plant will operate 350 days/year, find the energy kwh that the plant site can developed if the hydraulic turbine that will be used has an efficiency of 78% and generator efficiency of 90%. Consider a headwork loss of 4% of the available head.