A new coal-fired power plant has been built using a sulfur emission control system that is 70 percent efficient. If all of the sulfur oxidizes to SO2 and if the emission of SO2 are lmited to 0.6 lb SO2 per million Btu of heat into the power plant, what maximum percent sulfur content can the fuel have if 15,000 Btu/lb coal is burned?

A new coal-fired power plant has been built using a sulfur emission control system that is 70 percent efficient. If all of the sulfur oxidizes to SO2 and if the emission of SO2 are lmited to 0.6 lb SO2 per million Btu of heat into the power plant, what maximum percent sulfur content can the fuel have if 15,000 Btu/lb coal is burned?

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter1: Energy Basics

Section: Chapter Questions

Problem 19P

See similar textbooks

Similar questions

A 1000 MW coal fired power plant (30% efficiency). The coal is 75% carbon and has a heat content of 10, 000 BTU/lb. What is the carbon emission (ton carbon per year)?A 1000 MW natural gas plant (45% efficiency). The gas is CH4 with a heat content 800 BTU/mol. What is the carbon emission (ton carbon per year)?Calculate carbon emission reduction if the above natural gas plant is used to replace the coal fired plant.(Here ton is metric ton, 1 ton=2,200 lb)
A 440-MW coal-fired power plant is burning coal that contains 185 ppb of mercury. The coal firing rate is 300,000 Ib/hr, and the flue gas flow rate is 1.0 million scfm
Which emits more SOx per unit amount of electricity produced; a coal-fired plant with a 90% efficient SO2 scrubber or an oil-fired plant with m scrubber? Assume the coal has a heat content of 13,000 Btu/lb and contains 3.5% sulfur, and that the oil has a heat content of 6.0(10)* Biu/barrel (42 gallons) and contains 0.9% sulfur, Assume the oil has a specific gravity of 0,92.
The principal component of LPG is butane, C4H10 (g). If combustion of 1 mole ofbutane produces 126 kJ of heat, how much heat can be generated by completecombustion of one 11.0 kg gas tank?
Consider a new 38% efficient 600-MW power plant burning 9,000 Btu/lb coal containing 1% sulfur. If a 70% efficient scrubber is used, what would be the emission rate of sulfur (lb/hr)?
An anaerobic digestion system generates 10,000 m3 (353,150 standard ft3) of biogas per day. The produced biogas is to be used in an engine generator for generating electricity for wastewater treatment plant operations. How much electricity can be generated from the biogas? Answer: 21,795 kWh/day.
Determine the amount of SO2 released from the combustion of 1500 gallons of waste oil (135,000 BTU/gal) with 1.6 wt % S. The oil has a specific gravity of 0.86. How much reduction would this need to meet NSPS for a 125 MW electric utility steam generation source (35% efficiency)?
An incinerator burns 180 lb/hr chlorobenzene and has a stack gas containing 7% oxygen by volume on a dry basis. Determine the percent excess air .
(a) Locate, from an appropriate source, the composition for methanol and ethanol. Write down the formulas for the combustion of these two hydrocarbons. (b) Calculate the mass of CO2 produced per kg of methanol and ethanol burned. (c) Locate values for the heat of combustion of methanol and ethanol and determine the mass of CO2 produced per MJ of energy.
The ideal equation for the combustion of cellulose is C6H10O5 + 6O26O2 + 5H2O. What is a similar idealized equation for pyrolysis? What end products might you expect?
Cellulose is to be burned in a waste-to- energy fadlity. The chemical equation for cellulose C6 H10O5is the atomic weights of C, H, and O are 12, 1, and 16. respectively. a. Calculate the stoichiometric oxygen necessary for the combustion of cellulose. b. Calculate stoichiometric air.