A non-inverting amplifier is implemented using an LM741 operational amplifier. In the shown circuit, both Rs and Rp are 4.7 kN. The LM741 has the following parameters: Agiven = ay = 200, 000 Rin = 2 MN • Rout = 75 N Vin o- LM741 o Vout Rout V4 o MoVout RF Rs Vid Rin | AyVid (a) Non-Inverting Amplifier (b) Equivalent Circuit of the Op Amp 1. What is the feedback signal at the input (s f1)? Choose... + voltage or current? 2. What is the sampled signal at the output (sout)? Choose. voltage or current? 3. What is the feedback topology of the non-inverting amplifier? Oshunt-Shunt Oshunt-Series Oseries-Series OSeries-Shunt

A non-inverting amplifier is implemented using an LM741 operational amplifier. In the shown circuit, both Rs and Rp are 4.7 kN. The LM741 has the following parameters: Agiven = ay = 200, 000 Rin = 2 MN • Rout = 75 N Vin o- LM741 o Vout Rout V4 o MoVout RF Rs Vid Rin | AyVid (a) Non-Inverting Amplifier (b) Equivalent Circuit of the Op Amp 1. What is the feedback signal at the input (s f1)? Choose... + voltage or current? 2. What is the sampled signal at the output (sout)? Choose. voltage or current? 3. What is the feedback topology of the non-inverting amplifier? Oshunt-Shunt Oshunt-Series Oseries-Series OSeries-Shunt

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Assuming R11 and R12 as resistors connected to the inverting input, R2 - connected between the inverting input and the output, R13 - connected to the non-inverting input, please select elements of the circuit with an operational amplifier that will perform the function: V2 = -2V11 – 4V_12 + 7V_13. The result should be written in the format R1 = 111kOhm, R2 = 111kOhm, R3 = 111kOhm.
here im asked to find vx the way it was solved is that a node A was taken just before the op amp and nodal analysis aka kcl was applied and the node after it was called v0. but how did we name the first one A and the 2nd one v0? on what basis? also if im asked to get vx how do i think of taking the node A to get an equation so i can get Vx? what should i look for? im really bad at knowing what nodes to take and apply kcl or nodal analysis on to reach my desired solution so can you please help me with that? at the end of the answer it said vx=v0.2R / R+2R getting -2rA0 please can you address all my points so i can understand what and how to look for when solving this type of question?
For the circuit above, R= 4MΩ and C = 0.75μF. Vi(t)= −t^2V for 0s≤t≤5s. What is the value of Vo at time t=5s, if Vo(0) = 0? You can assume the operational amplifier behaves as an ideal op amp with power supplies of +15 and -15. Give your answer in volts.
You are given the following circuit. Assume that V1 = 6.2 V, V2 = 5.6 V, V3 = 7.1 V, V4 = 4.9 V, V5 = 7.6 V, R1 = 18 kΩ, R2 = 33 kΩ, R3 = 74 kΩ, R4 = 50 kΩ, and R5 = 29 kΩ. What is the voltage vn at the inverting terminal of the op-amp?( need only handwritten solution .otherwise downvote.)
An op-amp circuit is built with VS+ = +10V and VS- = 0V. The inverting input is grounded, and a signal v(t) = 1.0 V cos (ωt) is connected to the non-inverting input of the op-amp. Sketch the input and output of the op-amp at the same graph.
You are given the following circuit. Assume that V1 = 6.8 V, V2 = 6.5 V, V3 = 6.5 V, V4 = 6.7 V, V5 = 7.5 V, R1 = 79 kΩ, R2 = 11 kΩ, R3 = 53 kΩ, R4 = 79 kΩ, and R5 = 15 kΩ. What is the voltage vn at the inverting terminal of the op-amp?
Design a differential amplifier with tail resistor , using ±12V supplies such that Itail ≈ 4mA. Set RC1 = RC2 = 5kΩ. Ground the inputs and solve for RT. (My answer for RT is 2.8 kOhm)
Use the Thevenin and/or Norton theorems to determine the output voltage, V0,and the gain, G, of the op amp circuit. Please show all work and explain the steps a bit:)
a) A source vs = 2 V with internal source resistance Rs =10 kΩ applies a signal to a5 gain inverting amplifier with R1 =20 kΩ and R2 =100 kΩ. find the voltage ofoutput and verify that if a load is connected it will receive less than 10 V. (b) Find the value atthat we should change R2 to compensate and obtain 10 V at the output. present calculations
The Op amp in the circuit below is ideal. (a) Find the transfer function T(s)=VO/Vi of the circuit below. (b) What type of STC network is it?
MechatronixOne is a manufacturer of an industrial and toy robots. They are in the planning stage to develop a prototype AI robot for industry that will be supplied by a 12V dc. This AI robot as they envision has a capability to understand little English command and can interpret it. Their problem is how to design an RC filtered power supply that can be used in their prototype AI robot which has a load range of 250Ω to 1.25k Ω and since this is just a prototype it must be wired to the 220V peak ac supply in their laboratory. They ask the VoltageMaker Company to ship them 20 pcs of 12V dc power supply and it must be included in the data sheet the load current in rms and peak, the PIV, the power range absorbed by the load, the ratio of the transformer, and the secondary rms voltage of the power supply. The power supply must be in a bridge type. But sad to say the company is not producing this type of power supply. The management of VoltageMaker tasks their design engineer team to develop…
What is the quiescent current in the class-AB stage as shown if Kp = 400 μA/V2, Kn = 600 μA/V2, VT P = −0.8 V, and VT N = 0.7 V?