A non-inverting op amp configuration is shown.a. Find the gain of the amplifier, vo/vs.b. If vs =c. If v,d.If v,S1 V, what is the voltage at the output of the op amp?8 ΚΩVs+1 V, what is the voltage at the non-inverting (+) terminal of the op amp?1 V, what is the voltage at the inverting (—) terminal of the op amp?56 ΚΩww+12 V-12 V+12 kΩ Συ.

Answered: Image /qna-images/answer/42d570c7-2c57-489e-b2d1-b9848201b09f.jpg

A non-inverting op amp configuration is shown. a. Find the gain of the amplifier, vo/vs. b. If vs 1 V, what is the voltage at the output of the op amp? = c. If vs = d. If vs 8 ΚΩ Vs 1 V, what is the voltage at the non-inverting (+) terminal of the op amp? = 1 V, what is the voltage at the inverting (-) terminal of the op amp? + 12 V ● -12 V 12 kΩ Σ 0,

A non-inverting op amp configuration is shown. a. Find the gain of the amplifier, vo/vs. b. If vs 1 V, what is the voltage at the output of the op amp? = c. If vs = d. If vs 8 ΚΩ Vs 1 V, what is the voltage at the non-inverting (+) terminal of the op amp? = 1 V, what is the voltage at the inverting (-) terminal of the op amp? + 12 V ● -12 V 12 kΩ Σ 0,

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

What is the summing amplifier output voltage vo as shown if v1 =2 sin 1000πt V, v2 = 4 sin 2000πt V, R1 = 1 k , R2 = 2 k , and R3 = 3 k ? What are the input resistances presented to sources v1 and v2? What is the current supplied by the op amp output terminal?
You are given the following circuit. Assume that V1 = 4 V, V2 = 6.8 V, V3 = 4.9 V, V4 = 7.2 V, V5 = 7.6 V, R1 = 97 kΩ, R2 = 26 kΩ, R3 = 46 kΩ, R4 = 49 kΩ, and R5 = 40 kΩ. What is the voltage vn at the inverting terminal of the op-amp?
For the circuit shown, determine the range (i.e., maximum and minimum values) of V1 such that the op-amp operates in the linear region. Assume that R1 = 9.4 kΩ , R2 = 1.6 kΩ , R3 = 4.0 kΩ, RF = 200 kΩ, V2 = 40 mV, V3 = 100 m, and Vcc = 5 V.
The circuit utilizes an ideal op amp 1)Find I1, I2, I3, IL and Vx. 2) If VO is not to be lower than -6V, find the maximum allowed value for RL. 3) If RL is varied in the range 200Ω to 600Ω, what is the corresponding change in IL and VO?
. What is the effect on f0 as Av increased? 2. What is the effect on rise time as Av increased? 3. Is funity a constant across a wide range of voltage gains? 4. How would the results of this exercise differ if an op amp with a considerably higher funity was used?
The op amp in the noninverting amplifier circuit shown has an input resistance of 400 kΩ, an output resistance of 5 kΩ, and an open-loop gain of 20,000. Assume that the op amp is operating in its linear region. 1. Calculate the voltage gain (vo/vg). 2. Find the inverting and noninverting input voltages vn and vp (in millivolts) if vg=1 V. 3. Calculate the difference (vp-vn) in microvolts when vg=1 V. 4. Find the current drain in picoamperes on the signal source vg when vg=1 V. 5. Repeat (a)–(d) assuming an ideal op amp.
For the circuit, assuming an ideal op amp, and given Vs = - 1.5 V, R1 = 1 K ohm, R2 = 15k ohm, and R3 = 5k ohm, answer the following question. (Annotate diagram to show branches and nodes.) (a) Find the currents in all the branches (b) Find the voltages at all nodes (c) Find the power dissipated in each resistor (a) Find the total power dissipated in all resistors (e) How much power is delivered by Vs? (f) Explain: where does the rest of the power come from?
A single-pole op amp has these speciﬁcations: Ao = 80,000 fT =5 MHz Rid = 250 kΩ Ro =50 Ω (a) Draw the circuit of a macro model for this operational ampliﬁer. (b) Draw the circuit of a macro model for this operational ampliﬁer if the op amp also has Ric = 500 MΩ.
Salohiddin, [2022-05-10 오후 9:12]The op amp in Fig. P5.12 is ideal. a) What circuit configuration is shown in this figure? b) Find v, if va = 1 V, vb = D1.5 V, and v. = -4V.C) the voltages va and vc remain at 1 V and -4V respectively. What are the limits on v, if the op amp operates within its linear region?
The inverting amplifier in the circuit shown has an input resistance of 500 kΩ, an output resistance of 5 kΩ, and an open-loop gain of 300,000. Assume that the amplifier is operating in its linear region. 1. Calculate the voltage gain (vo/vg) of the amplifier. 2. Calculate the value of vn in microvolts when vg=1 V. 3. Calculate the resistance seen by the signal source (vg). 4. Repeat (a)–(c) using the ideal model for the op amp.
Please show that gain = -(1-n)/(1+nA) , n = R1/(R1+R2) and compare to gain of ideal op amp. Calculate the input and output impedances, and lastly whats the point of the resistor R1//R2 on the non-inverting input? What would be the best value for this resistor? (pretending it wasn't given that the value is R1/R2).
The op amp as shown is used to increase the overall output resistance of current source M1. If VREF = 5V, VDD = 0 V, VSS = 15 V, R = 50 kΩ, Kn = 800 μA/V2, VT N = 0.8 V, λ = 0.02 V−1, and A = 50,000, what are the output current Io and output resistance of the current source?