A nylon rope is shown in the figure and it is supporting a load of 100 lbs is placed at the midpoint of the rope. a. (CILO3) Draw the free body diagram of the rope. b. (CILO2) Determine the magnitude and direction (with respect to the +x axis) of the tension on the rope. c. (CILO 1) Complete the sentence: If the tension of the rope is (less than/more than) the answer in 1.b, the rope will be more sag. For Question 1: 5ft 40 ft 100 lbs

A nylon rope is shown in the figure and it is supporting a load of 100 lbs is placed at the midpoint of the rope. a. (CILO3) Draw the free body diagram of the rope. b. (CILO2) Determine the magnitude and direction (with respect to the +x axis) of the tension on the rope. c. (CILO 1) Complete the sentence: If the tension of the rope is (less than/more than) the answer in 1.b, the rope will be more sag. For Question 1: 5ft 40 ft 100 lbs

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A supporting rope is loaded with a line load q(x) = q0 between points A and B. The rope shall be stretched such that the slope of the rope at point A is zero. If l = 10 m and h = 2.3 m, determine the (a) horizontal tensile force and (b) the maximum force in the rope. q0 (kN/m) = 20.627
A cantilever beam shown in Figure B2 is applied with point load of 10KN and pointmoment of 7KNm. By using Macaulay method:Sebuah rasuk terjulur dikenakan beban tumpu 10KN dan moment lentur 7KNmseperti yang ditunjukkan dalam Rajah B2. Dengan menggunakan kaedah Macaulay:i) Derive the moment equation for the beam Terbitkan persamaan momen bagi rasuk
For this Problem, kindly refer to our Textbook, Structural Analysis Fourth Edition By Aslam Kassimali. For the given beam on Problem 5.8 Page 217, calculate the Moment in kip-foot at Point A if the given 40kip loads from the figure are both replaced by 68kips. Express your answer in 2 decimal places. Include (-) negative sign if the moment is negative.
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. W= 3.7 kN/m. Round your answer to 2 decimal places.
For this Problem, kindly refer to our Textbook, Structural Analysis Fourth Edition By Aslam Kassimali. For the given beam on Problem 5.35 Page 220, calculate the Moment at B in kip-foot if the given 30kip concentrated load and 2kip/foot uniform load from the figure are both replaced by 76kips and 10kip/foot respectively. Express your answer in 2 decimal places. Include (-) negative sign if the moment is negative.
Determine fixed support reaction . I will upvote Give fast answer
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. w = 4.6 kN/m i need an answer right away. thank you
The 4-lb pulley has a diameter of 1 ft and the axle has a diameter of 1 in. If the coefficient of kinetic friction between the axle and the pulley is μk = 0.20, determine the vertical force P is applied horizontally to the left on the rope required to lift the 20-lb block at constant velocity.
The man pulls on the rope at a constant rate of 0.5 m/s. Determine the angular velocity andangular acceleration of beam AB when Ɵ = 60°. The beam rotates about A. Neglect the thickness ofthe beam and the size of the pulley.
Given a force F applied on the handles of the device, determine the force developed on the rod at A. Set F = 6 lb.
An extra flexible 8 × 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 70 kN of load. The wire rope has a length of 900 meters. The maximum speed is 3 m / s and the acceleration is 1.5 m / s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84 × 103 N/mm2. The weight of the rope is 53 N/m length. Determine the effective load during acceleration of load in kN.
Determine the reactions and draw the shear and moment diagram of the indeterminate beam given below using Consistent Deformation Method. Consider the support reaction at point C to be the redundant. 50 k 50 k -8 tt 8n 8 it 21 Upload Choose a File