A platform is attached to a pole by two bolts, as shown. A force F of magnitude 400N is applied at an angle of 0-30° at point A on the platform. The height h of the platform is 2m and the length from the center of the pole to the end of the platform m is 1m. The bolts are located at a distance d from the centerline equal to .1 m. The point D is located at height k above the ground equal to .3m. a) Replace the force F by an equivalent force-couple system acting at point D. b) Redistribute this force and couple by replacing it with two forces acting in the same direction as F, one at each bolt (points B and C). Determine the magnitude of these forces supported by the two bolts. m Ө F d d h

A platform is attached to a pole by two bolts, as shown. A force F of magnitude 400N is applied at an angle of 0-30° at point A on the platform. The height h of the platform is 2m and the length from the center of the pole to the end of the platform m is 1m. The bolts are located at a distance d from the centerline equal to .1 m. The point D is located at height k above the ground equal to .3m. a) Replace the force F by an equivalent force-couple system acting at point D. b) Redistribute this force and couple by replacing it with two forces acting in the same direction as F, one at each bolt (points B and C). Determine the magnitude of these forces supported by the two bolts. m Ө F d d h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QUESTION 1 THREE PINNED STRUCTURE The structure shown in Figure 1 below represents an elevation of a typical frame which is supported at nodes A and B as indicated. The frame is subjected to forces as indicated and has a hinge at D. Joint C is a rigid joint. Note: 120kN is perpendicular to member BD. 1.5m 5m 35 kN/m LU/NOR ▬▬▬▬▬▬▬▬▬ Elgure 1 1.5m 120 KN 45° M 1.5m 4 Draw a neat, fully annotated shear force and bending moment diagram, including the maximum in span moment where appropriate. S E
Problem 2. Determine the horizontal and vertical components of the pin reaction at (B) on ABC for frame shown in the Figure. 10 N A B 1.5m C D 56 N.m 3m E- F G cord + F 1 1 1 2m 1.5m 2.5m 0.25m 3m
2. Determine the magnitude of the pin force at B. 0.43 m 0.61 m 125 N-m B 0.43 m 0.43 m
Asystem of cables is shown and in a state of equllibrium. Using equilibrium equations, solve for the absolute value of the axial force in mermber CD (in kN). 平 P+60KN
2. For the frame shown below, determine the minimum diameters of the pin at B, C, and E if the shearing strength of the pin is limited to 35 MPa. 1 m 2.5 m B 3000 N 1.5 m C 2 m 2m Your answer
2. The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its line of action are unknown. The resultant of this force system is the couple-vector. (-1100i + 1500J)lbft. Determine P and its line of action. %D 1400 lb 200 lb 300 1b y 2. ft 3 ft 3 ft 4 ft
If the weight of the block shown is 90kN and to be located at the center of gravity G. What is the tension in cables DE, AC and BC for equilibrium? TDE = TÁC = ... TBC = ... B y 3 m 4m 6 m 4m 3m
What is the fixed end moment at A? 10 kN 3kN/m D 3m B 4 m 4 m
Q2: Reduce the system of forces and moment shown to (a) an equivalent two * .forces and couple system at A 5 KN 0.5 m 2 m 75° To.15 m 10.15 m A 500 N-m 1.2 kN
given the image, find the support reaction components at the pin joint A and the roller B 2 m 5 KN 7 kN•m 2m SIN
Question 3 Determine the reactive forces at support A and B. 6m A -8m 12m 40KN B
Calculate the support reaction at roller support A