A power-supply filter with DC output voltage of 9.2 V has a load resistor of 10 kQ. 9.6 V Vpc 9.2 V T = 8.3333 ms Ripple Factor = 8.6957% The Full Wave (Bridge) Rectifier Si Diodes Load Resistor Lp = 100 Ls What is the ideal DC output voltage of a capacitor-input filter? А) 3.18 V B) 6.36 V 10

A power-supply filter with DC output voltage of 9.2 V has a load resistor of 10 kQ. 9.6 V Vpc 9.2 V T = 8.3333 ms Ripple Factor = 8.6957% The Full Wave (Bridge) Rectifier Si Diodes Load Resistor Lp = 100 Ls What is the ideal DC output voltage of a capacitor-input filter? А) 3.18 V B) 6.36 V 10

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An Armstrong modulator is used to generate FM which is suitable for FM broadcasting.You are given input of narrowband FM signal with carrier frequency fc1 = 27 MHz anda frequency deviation Δf1= 17 kHz. Assume that the frequency multiplier with n = 3 andlocal oscillator frequency of 80 MHz. Calculate the output of the carrier frequency andfrequency deviation if additive frequency is selected by mixer. Explain your obtainedanswer.
A passive first order low pass filter is designed in way such that its cut-off frequency is 1 kHz. If the value of the resistance present in the filter circuit is 400 ohm, then what will be the value of the capacitance present in the filter circuit?
Need Help Asap What is an active low pass filter? Explain its impact and application in engineering problems.
Supply voltage:V1=10Vppsin(2πf) Desingning RC and RL Low conquer Passive filter circuits? Cutoff frequencies in these filter circuits fc=37200Hz BW=? R=? C=?
The function generator circuit in the EIA has been designed to generate a sinewave output voltage with an amplitude of 5 Vat a frequency of 1 kHz. The low-pass filter hasbeen designed to have a low-frequency gain of−1 and a cutoff frequency of 1.5 kHz. What arethe magnitudes of the undesired frequency components in the output waveform at frequencies of2, 3, and 5 kHz?
Why was the smoothing capacitor C1/47 not placed directly after the unit bridge? It was placed in its place in the circuit, where its work as a smoothing filter for the base voltage of transistor Q1 was deliberately stopped, but it works with the rest of the circuit elements. Capacitor C1 is isolated between transistor Q1 and the rest of the circuit by a diode (1N4001).
A diode noise generator is required to produce 10uV of noise in a receiver with an input impedance of 75 ohms, resistive, and a noise power bandwidth of200kHz. (These values are typical of FM broadcast receivers.) What must the noise current be through the diode?
Q 3 Bring out the advantages and disadvantages of microwave tube devices andsemiconductor devices.What are the most common types of microwave diodes and transistors in use give theirbasic features features and applications?What are the most common types of microwave ICs? Give details of the circuit elementsand applications
Design the following Butterworth IIR filters. Let Fs=8000Hz. Determine H(s) of the analog Butterworth prototype based on a normalized sampling frequency Fs=1Hz (to simplify the computations).NOTE: If a digital filter with fc=800Hz is to be designed with Fs=8000Hz, an equivalent filter with normalized frequencies fc=0.1Hz and Fs=1Hz can be designed instead. The normalized frequencies are computed by dividing all the original frequencies with the original Fs. Determine H(z) and the difference equation of the Butterworth IIR filter using Bilinear transformation with pre-warping.(a) 2nd-order Lowpassfc=800HzNote: The normalized frequencies are fc=0.1Hz and Fs=1Hz. Answer: H(s)= 0.4223/(s^2+0.919s+0.4223) y[n]=0.0675x[n]+0.1349x[n-1]+0.0675x[n-2]+1.143y[n-1]-0.4128y[n-2]
Explain the difference between active filters and passive filters in the context of electronic filter design.
q9- Calculate the (approximate) data rate to bandwidth ratio (R/B) if the energy per bit (E0) is 13 and noise power per Hertz (N0) is 12 and the signal to noise ratio (SNR) is given as 10 dB. Select one option: a. 13.9 b. None c. 9.2 d. 15.9 e. Cannot determine the solution as more information is needed Clear my choice
q9- Calculate the (approximate) data rate to bandwidth ratio (R/B) if the energy per bit (E0) is 13 and noise power per Hertz (N0) is 12 and the signal to noise ratio (SNR) is given as 10 dB. Select one option: a. 13.9 b. None c. 9.2 d. 15.9 e. Cannot determine the solution as more information is needed