A receiving system consists of three components, an RF amp with 16dB power gain and Te = 35K, a mixer with 2dB power gain and Te = 40K, and an IF amp with 25dB power gain and Te = 52K. For a bandwidth of 1MHZ: a. What is the total noise power at the input of the RF amplifier 4.0434fW b. Determine the receiver's noise figure. 1.1257 c. Determine the receiver's equivalent temperature. 36.83K

A receiving system consists of three components, an RF amp with 16dB power gain and Te = 35K, a mixer with 2dB power gain and Te = 40K, and an IF amp with 25dB power gain and Te = 52K. For a bandwidth of 1MHZ: a. What is the total noise power at the input of the RF amplifier 4.0434fW b. Determine the receiver's noise figure. 1.1257 c. Determine the receiver's equivalent temperature. 36.83K

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a modulating signal of 20khz that is applied to an FM modulator, whose modulation index (β) is a value of 4, then the real bandwidth will be:
H3. a. Bandwidth of a signal in the 250…255 MHz frequency band, b. The gain in decibels of the system with an input voltage of 30mV and an output voltage of 30V, and c. Find the total gain of the system consisting of components connected in series with 20 dB gain and -10dB loss. ?
Generally, why are capacitors used in filters more than inductors? What is the gain/loss in dB of a transmission line fed with 150 Watts but outputs 120 Watts? What is the gain/loss in dB of a circuit fed with 20 Volts and outputs 30 Volts? What is the input impedance of an Ideal Operation Amplifier?
Give the spectrum? Find the value of the signal bandwidth using the following bandwidth definition: 1- Half power bandwidth? 2- Noise equivalent bandwidth? 3- Null-to-null bandwidth? 4- 99% of power bandwidth?
A signal transmission line which has a source impedance of 75Ω is to be connected to a signal strength meter of impedance 50Ω which has a maximum display of 18dB. Calculate the values of resistors required in an L-pad attenuator circuit to operate the meter at maximum power (towards small impedance). And also determine minimum insertion loss and minimum attenuation in dB.
A 1.5MHZ carrier signal is modulated with 3.4kHz modulating signal. The modulated carrier voltage. is 28V, and 14V, min across a 100 resistive load impedance. a) Peak amplitude of the unmodulated carrier . b) Coefficient of modulation. c) Carrier power d) Sideband power . e) Total power. f) Upper and lower sideband frequencies. g) Bandwidth
-MCQ- FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The frequency deviation constant kf = 25 Hz/V, the carrier is a cosine sign with an amplitude of 10V and a frequency of 2000Hz. The FM modulated signal is passed through a bandpass filter and 90% of the power of the modulated signal remains. What is the bandwidth of the FM modulated signal in this case? a) 240hz b) 20hz c) 100hz d)200hz
For a mosfet amplifier circuit, how can I choose an input and output capacitor with poles at 10Hz and 100Hz? Where RC = 1/w.
For an FM modulator with a modulation index mf = 1, a modulating signalVm(t) = Vm sin(2π1000t) and unmodulated carrier Vc(t) = 10 sin(2π500kt),determinea) Number of sets of significant sidebandb) Their amplitudec) Then draw the frequency spectrum showing their relative amplitudesd) Determine the unmodulated carrier power for the FM modulator(assume a load resistance RL = 50 Ω)e) Determine the power in the modulated carrier and each side frequency,and sketch the power spectrum for the modulated wave.
Using the circuits shown in the figure calculate; a) What is the total decibel gain in dBm? b) What is the total power gain? c) What is the total voltage gain? d) What kind of circuit appears at the output? e) Sketch the ideal bode plot?
Given an FM modulator with a deviation sensitivity K1= 3.7 kHz/V and a modulating signal vm = 5.2 sin(2π1,906t), determine the carrier swing in kHz For an FM modulator with an unmodulated carrier amplitude Vc= 14 V, a modulation index m = 1, and a load resistance RL = 8 ohms, determine the power (in watts) in the modulated carrier The percent modulation of the sound portion of a TV signal is 85%. The maximum frequency deviation for the sound portion of the TV signal as specified by the FCC is 25 kHz. Determine the carrier swing (in kHz) of the signal. For an FM modulator with 40-kHz frequency deviation and a modulating-signal frequency fm= 13 kHz, determine the bandwidth (in kHz) using Carson's rule. Given an FM modulator with a deviation sensitivity K1= 1.4 kHz/V and a modulating signal vm = 3.9 sin(2π1,948t), determine the peak frequency deviation in kHz. The percent modulation of the sound portion of a TV signal is 73%. The maximum frequency deviation for the sound portion of the…
Q2. An FM transmitter is modulated with a single tone A, cos (2nA2t) and a carrier amplitude of A, volt. The output resistive load for no modulation is A, N and the modulation constant k, = A5 Hz / volt. For the given parameters, determine the following: 1- The average power in all sidebands. 2- The carrier power if the amplitude of modulating signal is reduced by 5 volts.