A rectangul3 the water. The gate is 4 feet in length and 5 feet wide. Answer the following questions. vater door shown in the figure below is hinged 3 1. Calculate the resultant force on the door. 2. Calculate the location of the resultant force on the door. 3. Neglecting the weight of the door calculate the minimum force (FA) needed to keep th door closed You may assume the outer surface of the door and the surface of the water are both exposed

A rectangul3 the water. The gate is 4 feet in length and 5 feet wide. Answer the following questions. vater door shown in the figure below is hinged 3 1. Calculate the resultant force on the door. 2. Calculate the location of the resultant force on the door. 3. Neglecting the weight of the door calculate the minimum force (FA) needed to keep th door closed You may assume the outer surface of the door and the surface of the water are both exposed

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 22P

See similar textbooks

Similar questions

From the given figure below, the gate supports a weight of 11000 lb. What will be the height of water where the gate will start to rotate due to the pressure of water if it has length of 16ft and is 8ft wide? Compute the total hydrodrastic force on the gate and location of hydrodrastic force from hinge.
Q1(a) Explain the difference between wetting fluid and non-wetting fluid (b) The 60m X 60m rectangular gate shown in Figure Q1(b) has its top edge located 3m vertically below the water surface. The gate is to be opened from its lower edge by applying a normal force by the shaft. Determine the minimum force F required to open the water gate. (Ignore Patm in all your calculations)
A rectangular gate AB in Figure 1 is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric pressure effects, compute the force, F on the gate and its center of pressure position X.
The 600-lb, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude of the hydrostatic force acting on the gate using the HYDROSTATIC PANEL EQUATIONS. Express your answer in kips. B. Determine the minimum force P required to open the seawater gate. Express your answer in kips.
A vertical rectangular gate weighs 6000 lbs and is 10 ft tall and 8 ft wide (into the paper). The gate slides in vertical slots in the side of a reservoir containing water. The coefficient of friction between the slots and the gate is 0.03. Determine the minimum vertical force required to lift the gate when the water level is 4 ft above the top edge of the gate. [Answer in units of lbs.]
A 15 kg box rests on a horizontal surface attached to a 5 kg box as shown below. Determine the acceleration of the system and the tension of the rope. μs = 0.4 μk = 0.35
Formulate the expression for calculating the pressure rise in elastic pipe due to sudden closure of valve. Name the devices which can prevent water hammer effect in pipe.
Water flows at a rate of 120 L/s in a 30 cm diameter horizontal pipe connected to a 20 cm diameter pipe through a vertical reducer bend. The change in water direction of the reducing bend is 120o. The vertical distance between the entrance and outlet of the bend is 1.5 m and the pressure at its entrance is 70KPa. The total weight of the bend material and water contained in it is 90 kg. Calculate the horizontal and vertical components of the force required to hold the bend in place.
A uniform bar AB weighing 424 kN, is fastened by a frictionless pin to a block weighing 200 kN as shown in figure below. At the vertical wall, f = 0.268 while under the block f = 0.20. Determine the force P needed to start the motion to the right.
Figure 4.44 shows a rectangular gate holding water behind it. If the water is 6.00 ft deep, compute the magnitude and location of the resultant force on the gate. Then compute the forces on the hinge at the top and on the stop at the bottom.
A pipe with a constriction is carrying oil with a specific gravity of 0.853. Water with lines filled with oil is contained in a manometer that taps upstream and downstream of the constriction. On the water, the manometer has a 300 mm differential reading. In foot-pound force per pound mass of oil, what is the pressure loss across the constriction? How many pounds per square inch are there?
A square gate 3 ft x 3 ft lies in a vertical plane submerged in water. Determine the total pressure force on the gate and the distance between the center of pressure and the centroid when the upper edge of the gate is at the water surface. Compare these values to those that would occur if the upper edge of the gate is 10 ft below the water surface. Pleas show all work I want to understand. Answers from Textbook: F=841 lb; yp-y = 0.5 ft and F=6450 lb; yp-y = 0.0652 ft