A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 – 28mm dia in two rows, compression reinforcement consists of 2 – 22mm dia, fc’ = 27.6MPa, fy = 414.7MPa, d’ = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m   The strength reduction factor has a value of _____. Note: Use three decimal places

Q: Defermine the reactions on the beam. Solve for the displacements and draw the shear and noment diagr...

A:

Q: Find the total head for points A and B Find the hydraulic gradient for the system What is the pressu...

A: The total head (H) in the soil is equal to the sum of the pressure head and datum head. The velocity...

Q: 300 kN 50 kN/m 6.0 m 3.0 m El is constant

A:

Q: A W8x31, A36 steel is used as a simply supported beam uniformly loaded over a span of 6.4 m.  If the...

A: Given data- A W8x31, A36 steel-Span of the beam (L) = 6.4 mZx = 498×103 mm3To Find-The ultimate unif...

Q: A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member.  It is 6.8 m long, f...

A:

Q: The bearings of backward and forward tangents are S 65 30' E and N 75 40' E, respectively. If the de...

A: The last solution I have provides contains some error in part third (c) I have corrected it giving n...

Q: Determine the tensile steel strain (in 5 decimal places) compatible with concrete strain of 0.003 fo...

A:

Q: A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 700 mm. It is...

A:

Q: constant head permeability test is performed on soil that is 2 cm x 2 cm square, and 2.5cm long. The...

A:

Q: OPEN CORPASS TRAVERSE. Given in the accompanying sketch pass traverse. alues accordingly. 23. the ob...

A: A sketch depicting the forward and back bearings of an open traverse is given. In accordance with th...

Q: Find the load combination for (dead load = 25 kN, live load = 10 kN, earthquake load = 9 kN).

A: Given data: Dead load = 25 kN, Liive load = 10 kN, Earthquake load = 9 kN.

Q: Question 14 A wide flange section has the following properties: bf = 200 mm tf = 7 mm d = 300 mm tw ...

A:

Q: A rectangular section is limited to a size of b = 350 mm and d = 630 mm to carry a dead load moment ...

A:

Q: Make a flowchart showing the procedure on design of structural steel beams with doubly- symmetric ho...

A: We have to make a flowchart showing the procedure on design of structural steel beams with doubly sy...

Q: te tw

A:

Q: A square footing 2.1 m x 0.31 m thick supports a 300 mm square column at its center. Column loads ar...

A:

Q: 2/34 A portion of a mechar K lows: Pennies and dimes roll down the 20 incline the last triangular po...

A: The given data is as follows: Inclination=20∘Mass of dimes=2.28 gmMass of pennies=3.06 gmSlant dista...

Q: 1. The stairs of a high rise reinforced concrete building consists of a flight of steps cantilever f...

A: Given data length of cantilever steps= 1.5 m assume n=15 we have to compute the area of steel r/f re...

Q: A fine sand sample is placed into a permeameter that supplies a constant head of 100 cm of water. Wa...

A:

Q: Determine variables requested below for a horizontal curve with the following characteristics. Lengt...

A: We have to determine the value of tangent of the given horizontal curve as per the given data in the...

Q: In the following manometer set-up, di is measured to be 10 in, d2 measures 4 in, d3 measures 14 in, ...

A: The pressure at any point in the system can be calculated using the unit weight of the fluid and the...

Q: A 3m Water 45° C 3m B. In the figure shown, the gate in the shape of an arc of a circle of radius 3m...

A:

Q: only SKETCH this traverse

A:

Q: 64 64 22 Drill 38 13 R32 114 CRS 45

A:

Q: A solid steel circular shaft is required to carry a torque of 40 kNm and a bending moment of 20 kNm....

A:

Q: hected on both legs with 12 mm diameter bolts. Given that s = 50 mm

A: consider figure for solution 

Q: distributed load of 35 kN/m over the entire span. Concrete weighs 24 kN/, concrete strength f'e- 21 ...

A:

Q: A symmetric I-shaped built up steel beam is composed of 190 mm x 16 mm flange plates at top and bott...

A:

Q: An axially loaded tied column must sustain the following service loads: Total Dead Load    = 1,000 ...

A:

Q: 9- At what speed must a ball be thrown upwards to reach a maximum height of 25m?

A: Given data : Acceleration due to gravity g=9.81 m/s2 Final velocity V=0 m/s Maximum height h=25 m   ...

Q: Estimate the error in evaluating the function f(x) = e2x* sin x %3D near the point x = 1.369, if the...

A:

Q: Determine variables requested below for a horizontal curve with the following characteristics. Lengt...

A: Given data: Length of curve = 1255' Radius = 1200' sta of PC 12+00 3 Lane road way. Design speed= 60...

Q: Determine the tensile steel strain

A:

Q: A T-shaped built up steel beam is composed of 150 mm x 10 mm flange plate at top and a vertical web ...

A:

Q: 60 DRAW THE THREE PROJECTION OF THE FOLLOWING SHAPE 42 30 50 16 90 50 20

A:

Q: how transit-oriented designs and Bus Rapid Transit systems can make transportation infr

A: Patterns of transportation and land use are intricately connected. Transportation infrastructure and...

Q: Analyze the given continuous beam by clapreyons' three-moment equation. 2m" 39' 3 4m

A: Given data:

Q: A timber beam of rectangular section 50 mm x 100 mm is simp x 10 mm steel strip securely fixed to th...

A:

Q: Problem 03 Situation 03. In each month, the data were gathered 1t Month 2ad Month Precipitation 50.2...

A:

Q: An axially loaded tied column must sustain the following service loads: Total Dead Load    = 1,000 ...

A:

Q: A constant head permeability test is performed on soil that is 2 cm x 2 cm square, and 2.5cm long. T...

A:

Q: An A36 tension plate is 10 mm thick is given below.  Bolts are 20 mm.  Given that s = 65 mm and g = ...

A: Given data in question  Diameter of bolt Guage distance  Bolt lines To find out  Net area along the ...

Q: A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member.  It is 6.8 m long, f...

A: Given, The Given section : W12×79 properties of the given Section are as follows:  A = 14,500 mm^2  ...

Q: Determine average precipitation

A: Given data : Depth of precipitation at station A PA=2.65 in Depth of precipitation at station B PB=1...

Q: *4-48. Draw the shear and moment diagrams for each member of the frame. The joints at A, B, and C ar...

A: Given,

Q: Situation 3] The bearing of the first tangent of a simple curve is N70.8°E while the second tangent ...

A:

Q: A steel hollow circular tube of unknown thickness is suspended from the ceiling as shown in the figu...

A: Given data in question  Elasticity modulus Length  Loading  Outer diameter  Deflection  To find out ...

Q: The pressure drop in a 15 cm dia horizontal pipe is 100 kPa in a distance of 10 m. The shear stress ...

A:

Q: SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the bear...

A:

Q: Question 13 The axially loaded column given in the following image is a W14x53 with L = 7 m: 2 m L 2...

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.