A rectangular beam has dimensions of 250 mm width and an effective depth of 430 mm. It is subjected to shear dead load of 102 kN and shear live load of 114 kN. Use f'c = 20.7 MPa and fyt = 276 MPa for 12 mm diameter U-stirrup. Design the required spacing of the shear reinforcement.

Q: Find 5 internal Forces of the truss members also Find all Zero Member forces. 50KN loo KN 50 KN…

A:

Q: Problem- A spillway discharges flood flow at a rate of 9 m³/s per metre width. If the depth of flow…

A: Given- Discharge per meter width- q=9 m3/s/m,depth of flow y1=46 cm=0.46 m, It is needed to find the…

Q: The beam shown will be constructed from a standard steel W-shape using an allowable bending stress…

A: Given-A standard steel W-shaped beam having an allowable bending stress of 22.9 ksi. Beam is simply…

Q: A pipe of diameter 300 mm and length 3500 m is used for the transmission of power by water. The…

A: Given: Diameter of pipe d=300mm=0.3m, Length of pipe L=3500 m, Total head at inlet H=500 m,…

Q: Problem#3: The lap joint shown is fastened by four 4-in.-diameter rivets. Calculate the maximum safe…

A:

Q: The beam shown will be constructed from a standard steel W-shape using an allowable bending stress…

A:

Q: Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6…

A:

Q: Solve Prob. 3.53 when the tension in cable AB is 306 lb

A:

Q: 1. 2. 3. What is the chlorine demand of a wastewater volume of 1200 m³/day treated with 20 kg/day.…

A: Given, Chlorine demand for various flowrates

Q: Calculate the OCR and OCM for the midpoint of the clay layer prior to fill placement. b) Calculate…

A:

Q: Compute the moment of the force F about point A for the conditions shown below. Determine Moment…

A: To find moment about point A

Q: Two 150 mm * 300 mm concrete cylinders with randomly oriented steelfiber contents of 0 and 2% by…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: If the sensitivity of a clay is four and it's undisturbed strength is 300 units, the dis- turbed…

A: Introduction: The given question is related with Geotechnical engineering . In this question we are…

Q: The bending strength of an over-reinforced beam is controlled by: concrete yielding reinforcing…

A: The correct answer is concrete yielding

Q: 6. DETERMINE THE COMPONENTS OF THE REACTION ON PIN A AND THE REACTION AT THE ROLLER B SHOWN IN…

A:

Q: A cantilever timber beam with a span of L = 3.6 m supports a uniformly distributed load w. The beam…

A: Using bending stress equation

Q: #3 Determine the maximum deflection between the supports A and B. EI is constant. Use the method of…

A:

Q: 3.50 When a force F is applied to the handle of the valve shown, its moments about the x and z axes…

A:

Q: The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The b 3/4-inch in…

A: Diameter of bolt=3/4 in Thickness of plate =5/8 in

Q: SetP1=2.7kN, P2=5.2kN. Determine the force in member state if the member is in tension or…

A: Given : P1 = 2.7 kN and P2 = 5.2 kN Determine forces in member AB, AE, BC, BE, CD, CE, DE ?

Q: a) Compute the allowable block shear strength of the plates in KN. b) Check the adequacy of the…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: , the maximum flow on

A: Given data,  Average free flow speed,VA=60 km/hJam density,Dj=120 veh/kmFind the maximum flow on the…

Q: 5. DETERMINE THE MOMENT OF THE FORCE ABOUT POINT O IF F IS 550N. 0.4 m FIGURE 5 0.3 m F 300

A: Resolve force in horizontal and vertical direction.  Moment (M) = r*F              Where,…

Q: The average surface flow of a reservoir in the month of June is 20 km². In the same month the avg.…

A:

Q: The top width and the depth of flow in a triangular channel were measured as 4 m and 1 m,…

A: Given- Velocity at 0.2 m depth- V0.2 =0.6 m/s, Velocity at 0.8 m depth- V0.8 =0.4 m/s, It is needed…

Q: Consider the beam shown in (Figure 1). Suppose that w = 9 kN/m Figure 4 m W B 3 m 1 of 1 Determine…

A: Given data  Find support reaction at A and C.

Q: In a 10 m side square shaped sedimenta- tion tank, the flow rate is 100 cum/h, and if the depth of…

A:

Q: 1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The 3/4-inch in…

A: Diameter of bolt=3/4 in Thickness of plate =5/8in To find effective net area

Q: horizontal curve on a two-lane highway is designed with a 610-m radius, 3.5-m lanes, and 80 kph…

A: Radius= 610 m   Lane = 3.5 m Design Speed= 80kmph = 22.2 m/s Reaction time = 2.5 sec Friction = 0.35

Q: Problem 1 (a) (b) compression. Answers: (a) RAx= Rcx = . For the given truss structure below:…

A:

Q: For the three-hinged arch shown below, determine the reaction components. Show all solution and…

A: To Determine :- Reaction components of the three hinged arch given.

Q: A piping system is designed for a group of people that need to pump water with a continuous flow…

A: Given: Flow rate Q=10 Ls=0.01m3s Internal diameter of pipe D=0.06 m Length of piping L=500 m Depth…

Q: Review Problem 4.8 Take that L = 13 ft. (Figure 1) Figure 1 of 1 Part A Replace the distributed…

A: Given : L = 13 ft To FInd : FR and X ?

Q: A test car starts from rest on a horizontal circular track of 105-m radius and increases its speed…

A:

Q: Flane surface oth surface When we classify the piles in accordance to the type of loading, then we…

A: Option (C) is correct. Depending on the type of loading the piles may be classified as Axial and…

Q: A cantilever timber beam with a span of L=2.1m supports a uniformly distributed load w The beam…

A:

Q: A beam is subjected to equal bending moments of M₂ - 3700 N-m. The cross-sectional dimensions are…

A: Mz = 3700N-m b = 175mm c = 33mm d = 73mm t = 3mm   To be find -  Centroid location, the moment of…

Q: A beam is subjected to equal bending moments of M₂ = 4400 N-m. The cross-sectional dimensions are b…

A:

Q: The beam shown will be constructed from a standard steel W-shape using an allowable bending stress…

A: Given: Allowable stress, σallow = 21.6 ksi Load, P = 47 kips L1 = 2.1 ft L2 = 6.3 ft

Q: In a 10 m side square shaped sedimenta- tion tank, the flow rate is 100 cum/h, and if the depth of…

A:

Q: 20 kN/m 4 m

A:

Q: Temperature monitoring systems are used in what methods and for what purposes?

A: Temperature monitoring system:- There in geotechnical areas, temperature meters are used to track…

Q: What is the difference between an arch and a cable? State the places where you have seen arches and…

A: Reference : Structural shapes and Structural analysis, Arch and cables To determine : - Arch and…

Q: A steel column of rectangular section 5 mm * 2mm and length 2 m is simply supported at both ends.…

A:

Q: An activated-sludge system is to be used for secondary treatment of 15,000 m3/d of municipal…

A:

Q: Confirm the validity of statements by writing (T) otherwise write (F) and gave your opinion for it.…

A: Answer:  Given statement is False (F)

Q: The circular water pipes shown in the sketch are following full. The velocity of flow (in m/s) in…

A: Given data- At section P- Diameter d=4 m, Velocity v=6 m/s, At section Q- Diameter d=4 m, Velocity…

Q: Determine the horizontal component of reaction and the vertical component of reaction at D. Also…

A: Given : P1 = 9 kN and P2 = 17 kN Determine the horizontal and vertical component of reaction at D ?

Q: Question- The silt factor is 1.2. If the channel is designed by Lacey's theory which has a mean…

A: Given- Silt factor f=1.2, Mean velocity V=1.5 m/s, It is needed to find the hydraulic mean radius of…

Q: Specify the number of compartments.

A: Given:- A reverse-air baghouse is to be designed for removing fly ash The flowing rate of the gas…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.