A rectangular block is 132 mm long in the X direction, 76 mm wide in the Y direction, and 65 mm thick in the Z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 205 kN tension in the X direction, 169 kN tension in the Y direction, and 233 kN compression in the Z direction. If v 0.3 and E = 199 GPa, determine the single uniformly distributed load in the X direction that would produce the same deformation in the Z direction as the original loading. Answer must be in kN. • Previous Next Not saved Submit Q ENG MS

A rectangular block is 132 mm long in the X direction, 76 mm wide in the Y direction, and 65 mm thick in the Z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 205 kN tension in the X direction, 169 kN tension in the Y direction, and 233 kN compression in the Z direction. If v 0.3 and E = 199 GPa, determine the single uniformly distributed load in the X direction that would produce the same deformation in the Z direction as the original loading. Answer must be in kN. • Previous Next Not saved Submit Q ENG MS

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870
What is the bending stress in the beam 1.8 meters from point A? A.10.24 MPa B.9.60 MPa C.7.68 MPa D.8.60 MPa What is the bending stress 20 mm from the top of the beam 1.5 meters from point A? A.4.838 MPa B.10.442 MPa C.9.247 MPa D.7.225 MPa What is the shear stress in the beam at point A? A.0.80 MPa B.0.33 MPa C.1.57 MPa D.0.48 MPa What is the shear stress 80 mm from the top of the beam at point B? A.0.1024 MPa B.0.8072 MPa C.0.1966 MPa D.0.4096 MPa
A plastic beam has a cross section with dimensions of a = 1.2 in., b = 4.2 in., d = 2.4 in., and t = 0.3 in. The centroid is located c = 1.015 in. above the bottom surface of the beam, and the moment of inertia of the shape about the z centroidal axis is Iz = 2.384 in. 4. For a shear force of V = 2200 lb, what is the maximum shear stress in the beam?
A dam 4 m on top, 18 m at the bottom and 25 m high contains water 20 m deep on its vertical side. Neglecting uplift pressure, what is the stress at the heel? Wt. of concrete is 2200 kg/m³ a. 39 773 kg/m²b. 38 000 kg/m²c. 43 452 kg/m²d. 34 414 kg/m²
shows the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the total ultimate load in kN concentrated at E induced by beam DEF using tributary area method.
If possible, answer in 3 decimal places, thank you. For the wood beam shown in Figure A, assume L=1.5 m and P=8 kN. The beam cross section shown in Figure B has dimensions of b=47 mm and d=232 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? Calculate the reaction forces By and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown for the forces By and Dy on the free-body diagram below. (Note: Since Dx=0, it has been omitted from the free-body diagram.) By= kN Dy= kN Determine the shear forces VA⁢B, VB⁢C, and VC⁢D acting in segments AB, BC, and CD, respectively. Note that the shear force is constant in each of these segments. When entering your answers, use the shear force sign convention. VA⁢B= kN VB⁢C= kN VC⁢D= kN…
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
Q In the figure below, two circular loads with respective diameters of 10 inches (254 mm) and 20 inches (508 mm) on centres are applied to a homogeneous half-space. 50 psi (345 kPa) of pressure is exerted on the circle. The elastic modulus of the half-space is 10,000 psi (69 MPa), and its Poisson ratio is 0.5. Find the vertical strain, deflection, and stress at point A, which is 10 in. (254 mm) below the centre of one circle.
A vertical force P of magnitude 20 kips is applied at point C located on the axis of symmetry of the cross section of a short column. Knowing that y = 5 in., determine (a) the stress at point A, (b) the stress at point B, (c) the location of the neutral axis. My question is why point B is under compression and point A is under tension?
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m 4 Magnitude of resultant, R 4314.04 5 Angle of resultant direction from x-axis, θx 86.01 6 Distance of resultant from C measured along line CD, X 9.116
A large uniform cylindrical steel rod of density ρ = 8.8 g/cm3 is 4.0 m long and has a diameter of 5.0 cm. The rod is fastened to a concrete floor with its long axis vertical. What is the normal stress in the rod at the cross section located at (a) 2.0 m from its lower end? (b) 2.5m from the lower end? Your answer