A rectangular waveguide is terminated with an unknown load. By using a slotted line, load VSWR is found to be equal to 2 and distance between two successive minima is 1.5 cm. When the load is replaced by a short, the position of a given minimum shifts 0.3 cm towards the generator. Find the normalized value of the load.

A rectangular waveguide is terminated with an unknown load. By using a slotted line, load VSWR is found to be equal to 2 and distance between two successive minima is 1.5 cm. When the load is replaced by a short, the position of a given minimum shifts 0.3 cm towards the generator. Find the normalized value of the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.14P

See similar textbooks

Similar questions

For 860 MHz carrier frequency and for the geometry and graph shown in figures Q3A and Q3B, determine: A) the loss due to knife-edge diffraction, and
A transmission line has an inductance of 4 mH/loop km and a capacitance of 0.004µF/km. Determine, for a frequency of operation of 1 kHz, the phase delay, the wavelength on the line, and the velocity of propagation (in metres per second) of the
Derive an expression for sag in a transmission line of equal height poles
1. What is the necessary condition for matching transmission lines? In addition, what is a micro strip line? 2. For a distortion less line α = 0.02dB/m, Z0 (R0) = 60Ω and C = 0.2nF/m. Find the resistance and velocity of wave propagation. [Do not forget the units.] 3. For a finite lossless transmission line with open-circuit termination, sketch Xio vs l. Indicate where the sketch is inductive and capacitive.
A 105MHz, 90 v peak signal is incident on a 50-ohm transmission line. The line is 125m long and is terminated in 300-ohm load. What is the SWR for this situation? Find the reflection coefficient.
For this transmission medium for Temperature as 294 °K, what will be the Noise power in this bandwith?
3/ By measuring the rf voltage amplitude along a line with voltmeter, it is found that the voltage standing wave ratio (VSWR) is 7. (a) What is the magnitude of the reflection coefficient of the load, |r|? (b) If the characteristic impedance of the line is 500 ohms, and the load is known to be purely resistive and to have a value greater than 500 ohms, what is its resistance?
A transmission line in air with characteristic impedance Z0=50 ohm is terminated with a load impedance ZL ohm. What is the propogation constant k of the transmission line (assuming a coaxial line) for a 100 MHz uniform plane wave? What is the equivalence impedance of Z(-l) at l=.75m when ZL=25-j200 ohm? Calculate the shunt admittance to be added at l=.75m so that the line matched.
Use the free space model to compute the free space path loss for a 900 MHz signal over a distance of 200 meters. Express your answer in dB. state the answer in the correct units and show all your computations to receive credit
a) Discuss the effect of primary constants of a transmission lines onsignal propagation b) Using mathematical theories discuss how the standing wave phenomenon comes about and what can be done to eliminate it completely. c) Develop an expression for voltage and current traveling on atransmission line assuming all its primary constants are uniformlydistributed.
A transmission line has characteristic impedance of 75 Ω and it is connected to receiver with ??=100−?50 Ω, using smith chart to find:i. Reflection Coefficient;ii. VSWR
Find the characteristic impedance and signal velocity for a transmission line consisting of two parallel strips with a width ω and a separation d. You can ignore fringing fields by assuming that they are sections of concuctors infinitely wide.