A reinforced concrete beam has a width of 250mm and an effective depth of 500mm. If F'c= 28MPa, Fy = 415MPa, determine the following: a. Maximum steel area for singly reinforced condition. b. Maximum design strength if the beam is singly reinforced. c. The required steel area if the beam is subjected to a dead load moment of 100KN.m and live load moment of 130KN.m.

A reinforced concrete beam has a width of 250mm and an effective depth of 500mm. If F'c= 28MPa, Fy = 415MPa, determine the following: a. Maximum steel area for singly reinforced condition. b. Maximum design strength if the beam is singly reinforced. c. The required steel area if the beam is subjected to a dead load moment of 100KN.m and live load moment of 130KN.m.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

O Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu:= 30-MPa fy:= 450-MPa b:= 280-mm d:= 510-mm A, 2410-mm d':= 50-mm A's:= 628-mm² b A', d'
A 300 mm X 500 mm exterior beam is reinforced with 25 mm main bars and 12 mm stirrups. The tension side has a steel area of 2450 mm² and the compression side has a steel area of 1480 mm². 60% of the tension steel area is laid out on the first layer, the remaining is on the second layer and the compression steels are on a single layer. Determine the following if the steel yield strength of the compression steel is 276 MPa, the steel yield strength of the tension steel is 415 MPa and the depth of the tension zone 340 mm: a. The compressive stress in the concrete. b. The net tensile stress. c. Ultimate Moment Capacity of the beam.
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f' = 25MPa 800 IDE 730 N12 ligs (fsv.f-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the combination load for the reinforcement concrete beam shown in Figure 3. Unit: KN/m with two decimal. 1.2G+1.5Q=w
A simply supported beam is reinforced with 5-25mm at the bottom And 2-20mm at the top if the beam. Concrete covering to centroid of reinforcement is 70mm at the top and 64 mm at the bottom. The beam has a gross depth of 450 mm and gross width of 300 mm. Fc’=28 mpa fy= 415 mpa. Assume bars are laid out in a single layer. calculate the following if the limiting tensile steel strain is 0.004 for ductile failure: a) depth if neutral axis from the extreme concrete compression fiber ( in mm, in whole number) b) design strength of the beam section ( in kn•m , in whole number) c) maximum service uniform live load over the entire span in Addition to a DL = 20 kn/m ( including weight of the beam) if it has a span of 6 m ( in kn, in whole number)
A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000 L17 in. 20 in. 3 #9 bars (A, - 3.00 in.) 3 in. -12 in.- Select one: a. 2525 psi b. 2412 psi C. 2615 psi d. 2817 psi
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
concrete floor slab 100 mm thick is cast monolithic with concrete beam 2.0 m on centers. The beams have a span of 4.2 m and have a web width of 250 mm, and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry; a) effective flange width of an interior beam in mm b) depth of uniform stress block at ultimate stage in mm ( round of to nearest whole number) c) tensile steel strain compatible with concrete strain if 0.003 ( round if 3 decimal places)
Subject: Reinforced concrete Design- Civil Engineering A simply supported rectangular beam has a width of 300mm and the distance to the centroid of tension reinforcement is 330mm. The tension reinforcement has an area of 2463mm.2 and the area of compression reinforcement placed 70mm from the compression face of the beam is 1231.5mm.2, fy = 415MPa, fc'=30MPa, balanced steel ratio of 0.031.The design strength using 0.90 as the reduction faction is Choices A. 282kN.m B. 245kN.m C. 254kN.m D. 228kN.m
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2
The T-beam shown in figure resulted from monolithic construction of the beam and slab. The effective flange width is 1100 mm and the uniform slab thickness is 120mm. Width of beam is 340 mm, total depth of the T-section is 590 mm. The centroid of steel is 70 mm from extreme concrete fiber. Concrete strength f’c= 21 MPa amd steel strength fy= 415 MPa. 1 Calculate the nominal strength of the beam for positive moment neglecting the contribution of the top reinforcement, KN-m A 428.55 B 503.20 C 355.96 D 637.52 2 Calculate the nominal strength of the beam for negative moment, KN-m A 289.88 B 275.53 C 311.67 D 325.48
3. A reinforced rectangular concrete beam having a width of 300 mm, effective depth of500 mm, fc’ = 24 MPa, fy = 415 MPa, 4 - 28 mmɸ, d’ = 65 mm. Present the following (a) actual steel ratio (b) maximum steel ratio (c) a(d) c (e) check if steel yields (f) ?steel(g) type of failure (h) reduction factor (i) moment capacity
Design the simply supported beam shown in the Figure 1 for flexure Consider the following data. Characteristic compressive strength of concrete, fck= 25 N/mm? %3D Characteristic tensile strength of steel, fyk = 500 N/mm? Effective cover to reinforcement is 30 mm Density of Block work = 20 kN/m3 Draw the cross section of the beam at the mid span Height of 200 mm thick wall above the beam is 4 m 200 mm - Imposed Load-20kN/m 600 mm - 6 m