A researcher was observing traffic along one lane of a rural highway. During a 1 minute time interval, ten vehicles were observed travelling 65, 64, 71, 66, 58, 72, 69, 66, 55 and 62 mph. Estimate the density (veh/mile). Provide your answer to the nearest tenth.

A researcher was observing traffic along one lane of a rural highway. During a 1 minute time interval, ten vehicles were observed travelling 65, 64, 71, 66, 58, 72, 69, 66, 55 and 62 mph. Estimate the density (veh/mile). Provide your answer to the nearest tenth.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter4: Traffic Engineering Studies

Section: Chapter Questions

Problem 7P

See similar textbooks

Related questions

Q: Problem 2: Draw the influence line for the vertical reactions at supports B, E, and G and the shear…

Q: Given the two-dimensional water jet (50° F) is deflected which is moving to by the two-dimensional…

A: Given data,Initial velocity=60 ft/secInitial jet is 0.3ft thickFINDPower per foot of the jet is…

Q: 1) For the state of stress shown in figure, use the Mohr's circle method to determine (a) The…

A: Normal stress about x-axis, Normal stress about y-axis, Shear stress, To find: (a)…

Q: 11-12. The rapid sand filter being designed for Laramie has the characteristics shown below. Using…

Q: Parkin and Owen (1986) report the following parameter values for anaerobic digestion of primary…

A: Half saturation constant, Maximum specific growth, Maximum specific substrate use rate, Endogeneous…

Q: Use the same data as in problem 1 except that the standard deviation of the entire population is…

A: Since mentioned that the standard deviation of the entire population is known to be 1.2 MPa, can use…

Q: X₁ = 22.79+ |X₂= 60-x₁ 37-21 Z am AV 22-79 X) 37.21 1X ₂ 50 kN/m 60 o 3 15m BY B BH LOWEST POINT…

Q: #7-16. Determine the value of a so that the displacement at C is equal to zero. El is constant. Use…

Q: Q2.) The cable supports a uniform load of 920 N/m. The lowest point of the cable is 1.2 m below…

A: Uniform load = 920 N/mThe lowest point of cable = 1.2 mTo find:a. Maximum tension of the cableb.…

Q: How do you get the valuse for V mid and V mean?

Q: Problem 9 3-14. The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. If the wire…

Q: Calculate the vertical reaction at B. L

Q: a. Calculate the moment of inertia (I) of the given cross–section b. Calculate the first moment…

A: Given:Required:Moment of inertiaFirst moment of area at 25 mm incrementShear stress distribution

Q: Prompts A drawing that shows an accurate layout of a piece of land. 2 A drawing that shows an…

A: Gievn data,5 statement is given and choose the correct option for each statementLet's choosing the…

Q: The 10 ft rectangular wooden column has the dimensions indicated. Determine the critical load if It…

A: Length of the column (L) = 10 ft x 12 = 120 inModulus of elasticity of material (Ew) = 1.6 x 103…

Q: The T-shape shown in the figure is used as a tension member. Given that the gross area Ag = 2556…

A: T- shape member properties:Gross area, Ag = 2556 m2Thickness of web, tw = 10 mmGross depth, D = 220…

Q: 1. Determine the components of the reactions at A and E (Hint: eventhough there are 4 unknowns, it…

Q: - For a given month, a 121 ha lake has 0.43 m/s of inflow, 0.37 m'/s of outflow, and the total…

Q: et P₁360 lb, P₂ = 270 lb. (Figure 1) ure FEF= Submit ▾ Part C FDF = Determine the force in member…

Q: Applying the (AMM) Area Moment Method Approach. Consider 150 mm x 200 mm section and E = 80 GPa.…

Q: Support reactions (Rax, Ray, Rb) -Draw the internal shear force diagram -Draw the internal bending…

Q: Q. 5 Determine the moments MBD, MDB, MDC, and MDE. El is constant. 200 KN A B 20 kN/m 5 m 5 m D C…

Q: Please answer the following and fill up the table using Principle of virtual work method only.…

A: A beam is loaded is as followsdeflection at joint A has tobe found out

Q: 9 kN-m 33 kN/m A By (KN): Cy (KN): C₁: C₂: EIBA (+): 2m 2 kN/m C +im -3 m- EISA (1+): Előo (1+):.…

A: Slope:Slope refers to the change in the angle or inclination of a structure, typically a beam or a…

Q: Determine the slope at B and the maximum displacement of the beam. Use using the conjugate-beam…

A: Determine the slope at B and the maximum displacement of the beam. Use the conjugate-beam method.…

Q: Calculate the vertical reaction at B. Let P = 11 kips and W = 4 kips/ft. Assume support at B as…

A: p=11kipsw=4kips/ftassumed B as roller

Q: Determine the reactions of the given beam using moment distribution method. w = = 25 kN/m, P₁ = 25…

Q: Questions #2 The discharge of the pipe system shown is 0.85 M/sec. The length of pipes 1, 2, 3,…

Q: For the structure in this figure , write an expression that would determine the horizontal…

Q: B. Find forces in members CF, CG and GE of truss (b) using appropriate sections 30 k 30 k 41 30 k- F…

Q: Q5) Determine the critical depth if the flow is 1.5 m³/s. The channel width is 2.5m 45

A: Flow rate (Q) = 1.5 m3/sChannel width (b) = 2.5 mThe critical depth (Dc) =?

Q: An industrial plant needs 1, 383,739 gallon of water per day which must be pumped from a lake to a…

A: Given data - Q = 1383739 gallon per day H = 273 ft = 83.2104 m L = 1779 ft = 542.2392 m D = 11 in =…

Q: What are the possible objectives of an Atterberg Limit Test?

A: The term consistency indicates about degree of firmness (i.e.) an ease with which soil can be…

Q: 2 kN/m 5 m 3 m 10 kN 2 m- B

Q: An open cylindrical vessel 1.2m in diameter and 2.1m high is 2/3 full of water. Compute the amount…

Q: SAMPLE PROBLEM 1: Properties of W 30 x 116 d = 762 mm A W 30 x 116 beam has the top flange…

Q: Only part B

A: A propped cantilever beam fixed at A and supported on roller at B.A point load P = 1kN is acting at…

Q: It is required to design a combined footing for two RCC columns spaced at 4.5 m C/C. The columns are…

Q: Part C Determine the maximum in-plane shear stress and average normal stress. Enter your answers in…

Q: Hydration of cement is exothermic process that generates heat. The table below shows the heat…

A: Option-a:This option implies that utilizing any of the specified cement components is unsuitable for…

Q: Applying the (AMM) Area Moment Method Approach. Consider 150 mm x 200 mm section and E = 80 GPa.…

Q: (3) Calculate the displ aluminum rod (AB) horizontal and ver. of B. A=400mmit a

A: Compute the elongation of each rod and the horizontal and vertical displacements of point B.

Q: Recall that the Tatooine community has a population of 600663 residents and generate 0.7 kg of solid…

Q: Q1: Draw the shear and moment diagrams for each member of the frame. Assume the support at A is a…

A: The diagram is shown in the above figure. We have to draw the SFD and BMD of the each member in the…

Q: H.w:-prove that 01 σe = Ao A

A: Ture stress is the ratio of force applied to the area of cross section at the time of measurement of…

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: LL = 25 kNDL = 50 kNU = 1.0Plate dimensions: 10 x 100 mmFactored load:P = 1.2 DL + 1.6 LL = (1.2x50)…

Q: A 1.5-mile section of a two-lane road has an AADT of 10,000. In a three-year period, there have been…

A: Fatal accidents = 6Non-fatal accidents = 12AADT = 10,000Road length = 1.5 miles

Q: For the roof truss shown, determine the axial forces in members AD, BD, DE, and DG and state whether…

A: Let us draw the given diagram and find the supporting forces.

Q: 3-21. The stress-strain diagram for a polyester resin is given in the figure. If the rigid beam is…

A: P = 80 kN or 80,000 N d = 40 mmD = 80 mm

Q: Find Oc, Sc using бс Virtual Work method

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: We have to determine density

VIEW

Step 2: Using formula of space mean speed and density

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A researcher was observing traffic along one lane of a rural highway. During a 1 minute time interval, ten vehicles were observed travelling 65, 64, 71, 66, 58, 72, 69, 66, 55 and 62 mph. Calculate the average time headway (s). Provide your answer to the nearest tenth of a second.
A researcher was observing traffic along one lane of a rural highway. During a 1 minute time interval, ten vehicles were observed travelling 65, 64, 71, 66, 58, 72, 69, 66, 55 and 62 mph. Using these spot speeds, calculate the time mean speed (mph). Provide your answer to the nearest tenth of a mph.
A researcher was observing traffic along one lane of a rural highway. During a 1 minute time interval, ten vehicles were observed travelling 65, 64, 71, 66, 58, 72, 69, 66, 55 and 62 mph. Using these spot speeds, calculate the space mean speed (mph). Provide your answer to the nearest tenth of a mph.
A researcher was observing traffic along one lane of a rural highway. During a 1 minute time interval, ten vehicles were observed travelling 65, 64, 71, 66, 58, 72, 69, 66, 55 and 62 mph. Estimate the average vehicle spacing (ft/veh). Provide your answer to the nearest integer.
A 12 ft long loop detector has observed six vehicles that have crossed the device in a 148 second period, for the following durations: 0.44; 0.48; 0.5; 0.41; 0.49; and 0.55. The six vehicles are 18, 21, 20, 23, 17 and 19 ft respectively. Calculate: c. How many vehicles per mile is the density, k?
The freeway detector recorded an occupancy of 0.255 over a 15-minute period. If the detector is 1.5 meters long, and the average vehicle has a length of 6.5 meters, what is the implied density of this measurement?
A civil engineer takes a public ride going to his firm. The average time for his trip is 24 minutes, with a standard deviation of 3.80 minutes. If the office offers coffee from 8:50AM to 9:00AM, and he leaves his house at 8:35AM. what is the probability (in percent) that he misses coffee?
A 12 ft long loop detector has observed six vehicles that have crossed the device in a 148 second period, for the following durations: 0.44; 0.48; 0.5; 0.41; 0.49; and 0.55. The six vehicles are 18, 21, 20, 23, 17 and 19 ft respectively. Calculate: e. How many vehicles per hour current value, q?
A one way, two-lane road is shared by buses and cars. Buses travel at speed 40 mph and carry 20 people. Cars travel at speed 60 mph and carry 2 people. The fraction of vehicles that are buses passing a stationary observer is 0.2. Answer the following questions: (a) From the perspective of a stationary observer, what is the average number of passengers per vehicle? (b) What fraction of the vehicles on an aerial photograph would be buses? (c) If we take a photo of the road, what is the average number of passengers per vehicle based on this photo?
Vehicle time headways and spacings were measured at a point along a highway, from a single lane, over the course of an hour. The average values were calculated as 4.3 s/veh for headway and 50 m/veh for spacing. Determine the density in veh/km ( round your answer in 3 decimals)
What role does reaction time play in applying the brakes to your car in emergency situations? Assume your car is traveling at 100 kph when a pedestrian suddenly crosses the street in front of your car. How far will your car travel before you can apply the brakes? Show your solution.What is the likelihood of running over the pedestrian? (Assume that you can bring the car to a stop in 10 m once you step on the brakes when you are driving at 50 kph.)
A 12 ft long loop detector has observed six vehicles that have crossed the device in a 148 second period, for the following durations: 0.44; 0.48; 0.5; 0.41; 0.49; and 0.55. The six vehicles are 18, 21, 20, 23, 17 and 19 ft respectively. Calculate: d. How many miles per hour is the rated speed, v?