A rigid block having a mass 5 Mg is supported by three rods symmetrically placed, as shown in the figure. Determine the stress in each rod after a temperature rise of 40 °C. Use EF200 GPa, a=11.7 um/m.°C, A=500 mm², Eb=83 GPa, as=18. 9 µm/m.°C, and Ab=900 mm?. L=0.5 m L=0.5 m L=1 m IW= 5000x9.81

A rigid block having a mass 5 Mg is supported by three rods symmetrically placed, as shown in the figure. Determine the stress in each rod after a temperature rise of 40 °C. Use EF200 GPa, a=11.7 um/m.°C, A=500 mm², Eb=83 GPa, as=18. 9 µm/m.°C, and Ab=900 mm?. L=0.5 m L=0.5 m L=1 m IW= 5000x9.81

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure.a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN? (detailed solution please)
1. In The given figure, calculate A. The resultant force at joint C in KN B. The resultant force at joint A C. The stress at Rod BC if it has an area of 150mm x 150mm.
Water is placed in a hydraulic press initially at 140 kPa absolute, the pressure is increased to 222538 kPa absolute. Using 2.5 GPa as the bulk modulus of elasticity for water, determine the change in the volume of water in percent.
I want Normal stress developed in segment AB. A homogeneous bar with a cross-sectional area of 400 mm2 is attached to fixed supports as shown inthe figure. It is subjected to lateral forces P1 = 20 kN and P2 = 50 kN. Determine the normal stressdeveloped in segments AB and BC. Answer: σAB = 80.55 MPa
Figure 1a shows a concrete beam supported by twosolid circular columns. Column AB is made from steeland column CD is made from aluminium, see the stressstrain graphs in Figure 1b. The concrete beam issubjected to the load P as shown in Figure 1a.1. Determine the normal stress in column AB andcolumn CD. 2. Determine the relative change in angle of point Cto A in degrees. Given: P= 100KN L1= 3m L2= 2m L3= 1m dAB= 60mm dCD= 60mm
Water is placed in a hydraulic press initially at 140kPa absolute, the pressure is increased to 222538kPa absolute. Using 2.5 GPa as the bulk modulus of elasticity for water, determine the change in the volume of water in percent.
A thin spherical shell 1 m in diameter with its wall of 1.2 cm thickness is filled with a fluid at the atmospheric pressure. What intensity of pressure will be developed in it if 175 cm3 more fluid is pumped into it? Also calculate the circumferential stress at that pressure and the increase in diameter. Take: E = 200 GN/m2, and Poisson’s Ratio = 0.3
A bar with a cross section of 2320 mm2 P = 180 kN carrying pressure force Rod length L = 50 cm and Modulus of Elasticity, E = 140 GPa Calculate the normal stress that will occur in the rod andFind the changed height
For the beam shown below, b = 6 in and h = 14 in. If the beam is subjected to a transverse shear for of V = 8 kip, determine the largest shearing stress in the beam. Express your answer in psi to the nearest whole psi
A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure. a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN?c. What is the maximum shear stress in MPa?
If P = 27 kN and if the diameter of rod 1 is 16 mm and the diameter of rod 2 is 12 mm, determine the axial normal stress in each rod in kilopascals. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
The rigid horizontal slab is attached to two identical copper rods. There is a gap Δ = 6.18 mm between themiddle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 81°C. Use the following data: