A rigid block of mass m can be supported in each of the four ways shown. Each column consists of an aluminum tube that has a 44- mm outer diameter and a 4-mm wall thickness. Using E= 70 GPa and a factor of safety of 2.9, determine the allowable mass for each support condition. (Round the final answers to one decimal place.) 4 m m (1) m The allowable mass for case (1) is The allowable mass for case (2) is The allowable mass for case (3) is The allowable mass for case (4) is 1 (3) kg. m kg. kg. kg. (4)

A rigid block of mass m can be supported in each of the four ways shown. Each column consists of an aluminum tube that has a 44- mm outer diameter and a 4-mm wall thickness. Using E= 70 GPa and a factor of safety of 2.9, determine the allowable mass for each support condition. (Round the final answers to one decimal place.) 4 m m (1) m The allowable mass for case (1) is The allowable mass for case (2) is The allowable mass for case (3) is The allowable mass for case (4) is 1 (3) kg. m kg. kg. kg. (4)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

determine the reaction at A In kN using Double Integration Method Consider 150 mm x 150 mm section and E-200 GPa Enter the absolute value only and round off your answer to 3 decimal places. PLS ANSWER ASAP. I'LL RATE, THANKS
A conductor with a specific gravity of 40.10-3 kg/m.mm2 was drawn between two poles, which are given in the figure and erected on a valley slope, with a tension of 10 kg/mm2. Accordingly, find the conductor stress at the high suspension point. Please answer in very short i will like.. Please answer short and dont reject
A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial loadof 10 kN at bottom end. Calculate the elongation of the bar at a distance 2 m from thebottom end. Take the unit weight of the rod material is 25 kN/m' and modulus ofelasticity of the material is 3x109 MPa.
A cylindrical steel tank is manufactured based on the following data:internal pressure: 2460 psifactor of safety with respect to YP: 2.0yield stress in tension (circumferential): 56 000 psiyield stress in shear (longitudinal): 22 000 psi(a) Determine the minimum wall thickness if the diameter of the cylindrical steel tank is 7 inches.(b) Determine the maximum acceptable internal pressure if the wall thickness is 0.50 inches.Use 2 decimal places in every solved values. (25 pts)
A hollow circular column of internal diameter 20 mm and external diameter 40 mm has a total length of 5m. One end of the column is fixed, and the other end is hinged. Find out the crippling stress of the column if E = 2 × 10^5 N/mm2. Also, find out the shortest length of this column for which Euler’s formula is valid taking the yield stress equal to 250 N/mm2.
A square plastic bar (length Lp, side dimension sp = 193 mm) is inserted inside a hollow, square, cast iron tube (length Lc = 400 mm, side sc = 200 mm, and thickness tc = 3mm). (a) What is the required initial length Lp of the plastic bar so that, when it is compressed by some force P, the final length of bar and tube are equal to legnth Lc, and, at the same time, the gap between plastic bar and cast iron tube is closed? (b) Compare initial and final volumes for the plastic bar. Assume that Ec = 170 GPa, Ep = 2.1 GPa, vc = 0.3, and vp = 0.4.
A hollow steel (E= 30,000ksi) tube (1) with an outside diameter of 2.75in. and a wall thickness of 0.25in. is fastened to a solid aluminum (E= 10,000 ksi) rod (2) that has a 2in. diameter and a solid 1.375in. diameter aluminum rod (3). The bar is loaded as shown in the figure. Determine (a) the change in length of steel tube (1); (b) the deflection of joint D with respect to the fixed support A. (c) the maximum normal stress in the entire axial assembly.
The column shown in the figure is loaded with a vertical load P = 3kN and lateral load H = 0.45kN. The column is 3m high and is made of steel with 300mm outer diameter, 6mm thick and weighs 150N/m. What is the maximum stress at the base due to the load P?
A steel column of hollow circular cross section is supported on a circular, steel base plate and a concrete pedestal (see figure). The column has an outside diameter d = 250 mm and supports a load P - 750 kN. (a) If the allowable stress in the column is 55 MPa, what is the minimum required thickness? Based upon your result, select a thickness for the column, (Select a thickness that is an even integer, such as 10, 1 14,.. ., in units of millimeters.) (b) If the allowable bearing stress on the concrete pedestal is 15 MPa, what is the minimum required diameter D of the base plate if it is designed for the allowable load Pallow that the column with the selected thickness can support.
A pan of negligible mass is attached by two identical springs with stiffness k = 250 N / m. A 10 kg box is dropped from a height of 0.5 m on the ceiling. Determine the maximum amount of vertical displacement (d). Initially, each spring has a tensile force of 50 N.
The crankshaft is subjected to a torque of M = 50 N ⋅ m. Determine the horizontal compressive force F and plot the result of F (ordinate) versus θ (abscissa) for 0° ≤ θ ≤ 90°.
A line load of q=60kn/m with alpha =300 is placed on a ground surface as shown in figure p4.1.Calculate the increase of pore water pressure at M immediately after application of the load for the cases given below. (a) z=10m ,X=0m ,v=0.5 ,A=0.45 (b) z=10m, X=2m,v=0.45, A=0.6