A rigid tank of volume 10 m³ initially contains saturated water vapor at a temperature of 120 °C. Steam at a pressure 1.2 MPa and a temperature of 400 °C enters the tank through a valve in steam line that is connected to the tank until the final pressure in the tank is 800 kPa, at which time the temperature is 200 °C. All kinetic and potential energy effects can be neglected. A schematic of the problem and properties at all state points except state 1 are shown in the figure below. All of the properties at state 2 and the inlet state i are provided on the figure. Initial State in Tank T₁-120 °C, Sat. vapor u₁=? kJ/kg V₁=? m³/kg Pi=1.2 MPa, Ti-400 °C hi-3261.3 kJ/kg V=10 m³ Final State in Tank T: 200 °C, P₂-800 kPa u₂=2631.1 kJ/kg v₂=0.26088 m³/kg Qout

A rigid tank of volume 10 m³ initially contains saturated water vapor at a temperature of 120 °C. Steam at a pressure 1.2 MPa and a temperature of 400 °C enters the tank through a valve in steam line that is connected to the tank until the final pressure in the tank is 800 kPa, at which time the temperature is 200 °C. All kinetic and potential energy effects can be neglected. A schematic of the problem and properties at all state points except state 1 are shown in the figure below. All of the properties at state 2 and the inlet state i are provided on the figure. Initial State in Tank T₁-120 °C, Sat. vapor u₁=? kJ/kg V₁=? m³/kg Pi=1.2 MPa, Ti-400 °C hi-3261.3 kJ/kg V=10 m³ Final State in Tank T: 200 °C, P₂-800 kPa u₂=2631.1 kJ/kg v₂=0.26088 m³/kg Qout

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Similar questions

A steel casting weighing 2 kg has an initial temperature of 500oC; 40 kg of water initiallyat 25oC is contained in a perfectly insulated steel tank weighing 5 kg. The casting isimmersed in the water and the system is allowed to come to equilibrium. What is its finaltemperature? Ignore effects of expansion or contraction, and assume constant specific heatsof 4.18 kJ/kg.oC for water and 0.5 kJ/kg.oC for steel.
A boiler takes in feed water at 70 °C and generates steam at a pressure of 10 bar and drynessfraction 0.92. The wet steam enters a superheater and emerges with the same pressure at atemperature of 400 °C. If the steam flow rate is 5 tonnes per hour, determine (i) the rate atwhich heat transfer takes place in the boiler and (ii) the rate at which heat transfer takes placein the superheater. State any assumptions you have made in relation to the steady flowequation for the process.
A flashed steam geothermal powerplant is located where underground hot water is available as saturated liquid at 700 KPa. The well head pressure is 600 KPa. The flashed steam enters a turbine at 500 KPa and expands to 15 KPa. When it is condensed. The flow rate from the well is 29.6 kg/sec. Determine the power produced in KW. Can you show me the solution with a hand written.tnx in advance
Water Vapor pressure 8 MPa and 350 in an adiabatic turbineIt enters at a temperature of oC and at a pressure of 750 kPacomes out. Reversible The amount of work done by the unit mass of steam for the processcalculate.
Please indicate the given. Determine the optimal intermediate pressures and work needed per kilogram of gas for a three-stage compressor that must compress air between 120 kN/m2 and 288 K to 3800 kN/m2. It's likely that the compression is adiabatic, and that interstage cooling is being used to cool the air back to its initial temperature.
Box the final answer. Write legibly. Steam flows into a turbine at a rate of 3.5 kg/s and ¾ MW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine in KW? Steam pressure entering the turbine is 62 Bar at 440ºC and leaves at 74 Kpa.
With a 50 m^3 capacity, a tank contains steam at 400 degrees Celsius and 4500 kPa. From the tank, steam is vented through a relief valve to the atmosphere until the pressure in the tank falls to 3500 kPa. Assuming the venting process is adiabatic, estimate the steam's final temperature in the tank and the mass of steam vented. (Please help me understand the trial and error part for determining the required amounts by solving.)
Water enters a boiler at 18.33 °C and 137.9 kPa through a pipe at an average velocityof 1.52 m/s. Exit stream at a height of 15.2 m above the liquid inlet leaves at 137.9 kPaand 148.9 °C at 9.14 m/s in the outlet line. At steady-state, how much heat must beadded per kg mass of steam? The flow in the pipe is turbulent.
Steam at a pressure of 11 bar and a temperature of 320C is containedin a large vessel. Connected to the vessel through a valve is a turbinefollowed by a small initially evacuated tank with a volume of 0.60 m3.When emergency power is required, the valve is opened and the tankfills with steam until the pressure is 11 bar. The temperature in the tankis then 400C. The filling process takes place adiabatically and kineticand potential energy effects are negligible. Determine the amount ofwork developed by the turbine in kJ.
can you please solve this for me, thanks. 10 kg/s of steam (H2O) enters a turbine at 10 m/s and a specific enthalpy of 3500 kJ/kg and leaves at an outlet 10m below the inlet with a specific enthalpy of 2500 kJ/kg and a velocity of 20 m/s. Assume steady-state steady-flow. If the heat lost from the turbine is 20% that of the turbine work, determine a.) the turbine horsepower. If the turbine is coupled to a generator with a 90% electrical efficiency, and the turbine horsepower has an 80% mechanical efficiency, b.) how much income will a power plant generate in one year if the electrical energy is sold at PhP 3.51 per kW-hr? (Hint: Mechanical efficiency = actual turbine work / ideal turbine work. Electrical efficiency of a generator = electrical output / actual turbine work.)
Show solution A two stage air compressor has a suction volume of 700 m^3/hr at 100 kPa and 22 ℃ discharges to 690 kPa. Determine the heat rejected (in kW) in the intercooler.
An adiabatic piston-cylinder device equipped with aspring maintains the pressure inside at 300 kPa, when thevolume is 0, and in 3 000 kPa, when the volume is 5 m ^ 3. Thedevice connects to a steam supply lineat 1,500 kPa and 200 ° C, and at the beginning the volume of the cylinder is 0.Determine the final temperature (and quality, if applicable) whenthe valve is opened and water vapor is allowed to enter from thesupply to the cylinder, until the pressure inside is equal tothe one on the line. Also determine the total workperformed during this adiabatic filling process.