A rigid vessel having a volume of 0.4 m3 is filled with steam at 800 kPa and 350 o How much heat has to be removed to bring the temperature of the steam to 200 oC? Follow the guide below

Q: 7. a). Barnett Reservoir, the north-west section was eroded much, adding limestone (CaCO3) to stabil...

A: Henry constant for CO2 : KCO2=3.38×10-2 M/atm Ka1 for CO2 in water = 4.47×10-7 K for CaCO3  dissolut...

Q: 17. Prove that : the mass transfer flux can be calculated from NA=N X4+ JA

A:

Q: Two bulbs are connected by a straight tube, 0.001 m in diameter and 0.35 m in length. Initially the ...

A:

Q: Explain the reason for the design of the gaseous fuel burner wherein there are the following feature...

A: Along with fuel there is requirement of sufficient quantity of oxygen to carry out combustion. Hence...

Q: Biogas system design for cooking for a family of 9 members is considered here. The system design inc...

A: A family of 9 members is considered  The system is designed for maximum load The maximum range  of b...

Q: In a double-pipe counter-flow heat exchanger, water is heated by steam condensing at 130°C (hfg=2203...

A: Given Cooling and heating fluid parameters and tube dimensions/ overall heat transfer coefficient fo...

Q: Cooling water available at 10°C is used to condense steam at 30°C in the condenser of a power plant ...

A: Condensers are used to condense steam, which works on the principle of a Heat exchanger. There many ...

Q: Natural gas containing CH4 and C3H8 is burned with air containing 21% O2 and 79% N2. As a result of ...

A: In the flue gas Amount of oxygen is 21% Amount of carbon dioxide is 1% Amount of oxygen is 6% Air co...

Q: The student placed a 200gram woodrat that had been orally dosedwith a water solution in the calorime...

A:

Q: Nitrogen flows at steady state through a horizontal, insulated pipe with inside diam- eter of 1.5(in...

A:

Q: A fluid with a density of 1.03 g cm-³ is flowing at the rate of 1.8 L h-' through a small tube that ...

A: Density of the fluid ρ = 1.03 g/cm3 volumetric flow rate = 1.8 L/h = =1.8×10003600 cm3/s =0.5 cm3/s ...

Q: Determine the transfer function H4(s)/Q0(s) for the liquid level systemshown in Fig. below. [Resista...

A: Four liquid level systems are connected in series. System is noninteracting.

Q: D e f

A: F1=F2+F5but F2=60 molminF3= 40 molminF1=100 molminFrom flow diagram yp=0.9                         t...

Q: Find the pH scale of the solution of acid H2SO4 of concentration 1.5 x 103 M. Use Ka= 1.2 x 10-2   H...

A: pH is the negative logarithm of hydrogen ion concentration. It is used for the determination of the ...

Q: how to solve this question?

A: GivenCombustion of methane as per the following reactions   Feed composition in mole %CH4=7.8%O2=19...

Q: In a packed bed tower air is purified from methanol by using water. Tower has a cross sectional area...

A: Given data: Cross-sectional area of tower = 4000 cm2 Operating temperature = 313.1 K Operating press...

Q: 6.1 A manufacturer blends lubricating oil by mixing 300 kg/rmin of No. 10 oil with 100 kg/min of No....

A: Note: As per the guidelines, we’ll answer the first question since the exact one wasn’t specified. P...

Q: Q1: Power of 12kW is supplied to a machine Crushing limestone from 8mm diameter average size to 0.2 ...

A: According to bond law, the power required per unit mass is given as Pm=0.3162*wi*1Dpb-1Dpa  Where Dp...

Q: A multicomponent distillation column has a minimum reflux ratio Rmin = 1.378, minimum stage number N...

A: Number of theoretical stages is asked. Given:Rmin=1.378Nmin=6.79R=1.25Rmin

Q: A carnot machine operating between 500 K and 298 K temperatures produces 1500J of work in each cycle...

A:

Q: The reaction specific heat is -3489.63. This reaction is self-sustaining or not? Why?

A: Given: ∆H= -3489.63 The negative sign indicates the reaction is an exothermic reaction.

Q: II. The most common electrodes used for measurement of corrosion potentials are: (Mark two correct a...

A: Corrosion occurs due to the formation of electrochemical cells, where there will be movement of elec...

Q: A zero-order reaction (A --> 4B) is to occur at a temperature of (127 C) in a variable volume batch ...

A: Order of the reaction A→4B is zero Temperature T1 = 127 °C Initial concentration of A is CA0 = 4 gmo...

Q: 1.Balance the following redox equations. All occur in acid solution a) Ag (s) + NO3 (aq) - NO2 (g) +...

A: As per Bartleby guidelines we are supposed to answer the first question only. Kindly resubmit other ...

Q: 7. Ammonia is manufactured using the reaction:N 2 + 3 H 2 → 2 NH 3. How much ammonia can be produced...

A: The following reaction is used for ammonia production N 2 + 3 H 2 → 2 NH 3.    

Q: Calculate the time, in seconds, required to deposit 56 mg of silver from a silver nitrate solution u...

A: Given data: Weight of silver which is to be deposited = 56 mg Current = 4.5 amp Molecular weight of ...

Q: Given RH 27.5%, wet bulb temperature 100 degrees F. Calculate what is the dry bulb temperature, dew ...

A: The dry bulb temperature, dew point, absolute humidity, specific volume and enthalpy has to be calcu...

Q: Write down in your homework that we will use the words "activity coefficient" in place of "fugacity ...

A: Note: Because you have asked a question with multiple subparts, we will solve the first three for yo...

Q: Consider a rigid container with 2 moles of an ideal gas initially at 8 bar and 337 o How much heat n...

A: Number of moles of the gas n = 2 moles Pressure, P1=8 bar Pressure, P2=1 bar Temperature, T1=337°C=(...

Q: A single crystal of aluminum is oriented for a tensile test such that its slip plane normal makes an...

A: Given data: A single crystal of aluminum is oriented. Angle between normal to the slip plane and app...

Q: Hundred kilograms per hour of wet steam at 25 bar with 90% quality is passed through a throttling va...

A: Given: Mass flow rate of steam, m = 100 kg/h The initial pressure of the steam, P1 = 25 bar The init...

Q: I need the solution quickly..please In 10 minutes

A: Note:We are authorized to answer three subparts at a time, since you have not mentioned which part y...

Q: Determine the reaction order and the coefficient using the following data obtained from a batch reac...

A:

Q: A piece of meat, 3 cm thick, which can be considered as an endless plate, has a homogeneous initial ...

A: Heat flow from outside to the surface of body= Increase in internal energy of body

Q: QI/ A gas analyzes 70% methane (MW: 16) and the rest is ethylene (MW: 28) by volume. It is desired t...

A: Hello. Since your question has multiple parts, we will solve the first question  for you. If you wan...

Q: Gas bulb A has a volume of 6.00 dm3 and contains N2 gas at a pressure of 200 kPa. Gas bulb B has a v...

A:

Q: Specific Heat When you have two identical pans of equal amount of water and oil, which do you think ...

A: Specific heat of a substance represents the amount of heat required to raise the temperature of 1 g ...

Q: 1. Why do we avoid cold and hot forming during cutting? . 2. Why is the sample rotated at an angle o...

A: Only the 1st question is answered here because the exact one is not specified.    Metal forming is a...

Q: Given RH 27.5%, wet bulb temperature 100 degrees F. Calculate what is the dry bulb temperature, dew ...

A:

Q: Q.5: Water is to be cooled in a packed tower from 330 to 295 K by means of air flowing counter-curre...

A: Given data: Water is cooled from 330 to 295K Liquid flows at a rate of 275cm3/m2s and air at 0.7m3/m...

Q: Q1: Often young children drink milk p= (1030 kg/m³) through a straw. Determine the maximum length of...

A: Suction lift occurs when the applied pressure is less than atmosphere. This term expresses mathemati...

Q: Raw sewage flow 5000 m/dmy having temp. of 30°6 is fed to lagoon having area 2000m estimate the mean...

A: Simple heat balance can be used to estimate heat loss effects on temperature of lagoon  Qi×Ti=Qe×Te+...

Q: 19

A: Diffusion is a process that mainly takes place due to the concentration gradient. There are various ...

Q: How do I do question 3 and 4.

A: NOTE: Since you have asked multiple questions, we will solve the first question for you. If you want...

Q: The eluate concentration is 257 mCi/ml. You are to make an HDP kit with 300 mCi, and the desired con...

A: Given: Eluate concentration = 257 mCi/ml HDP kit is to be made with 300 mCi The desired concentratio...

Q: 4. Given the molar Gibbs Free Energy G expression for a binary mixture: G=G, x, + G, x,+ x, X, (a x,...

A: Derivation of chemical potential and activity co-efficient.  

Q: What is the importance of proper application/implementation of aquaculture engineering in any fish f...

A: Aquacultural engineering is a multidisciplinary field of engineering that aims to solve technical pr...

Q: 5. How long will it take for concentration to fall from 100mg/l to 25mg/l if k = 0.2 hr-1? (first-or...

A: In chemical Reaction Engineering, A first-order reaction is reaction rate is linearly dependent on t...

Q: Chemical Engineering Question

A: NOTE:  Since you have posted a question with multiple sub-parts, we will solve the first three subpa...

Q: II. A galvanic series is

A: Galvanic series  A list of metals and alloys arranged in a chart with their  corresponding electroly...