A rod of length 1.6m long has a diameter of 0.5m wide. this rode is made of 52100 chromium steel with a yield strength of 586mpa and ultimate tensile strength of 723mpa. the von misses stress is 579 pa. please perform fatigue analysis of the rod. if I missed a number or parameter you need to perform the fatigue analysis you can choose a number that helps you solve this problem mainly by trying to understand the concept. Fpy forces in y direction are zero and fpx forces in x directiion is 200 newtons. Mp Mp

A rod of length 1.6m long has a diameter of 0.5m wide. this rode is made of 52100 chromium steel with a yield strength of 586mpa and ultimate tensile strength of 723mpa. the von misses stress is 579 pa. please perform fatigue analysis of the rod. if I missed a number or parameter you need to perform the fatigue analysis you can choose a number that helps you solve this problem mainly by trying to understand the concept. Fpy forces in y direction are zero and fpx forces in x directiion is 200 newtons. Mp Mp

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
An NDT examination of a steel component reveals the presence of a 5 mm long edge crack. If plane - strain conditions prevail (KIC = 75 MPa.m0.5), what would be the residual service lifetime of the steel part if it were subjected to repeated stresses of 400 MPa? The Paris law equation for the steel has parameters of A=4X10-37 and m = 4
Draw a fatigue loading spectrum (stress - time plot) for R = 0.5, and define the followings by writing the appropriate equations of them, and show them on the spectrum.(a) Maximum and minimum stresses,(b) Stress range,(c) Stress amplitude,(d) Mean stress,(e) Cycle.
A brittle material has the properties . Sut = 30 kpsi and Suc = 90 kpsi Using the brittle Coulomb-Mohr and modified-Mohr theories, determine the factor of safety for the following states of plane stress.
Analyse the differences between the 2 attached stress-strain curves for 0.9% carbon steel and 0.15% carbon steel.
A tie rod made of quenched and tempered 4340 steel is used as a critical linkage in an industrial apparatus. The rod is subjected to an alternating cyclic tensile/compressive stress from 550 MPa to -550 MPa. An inspection of the rod revealed a 3.5 mm deep edge crack on the surface of the rod. Please answer the following question for the rod given the properties in the table and curve below and fracture toughness of 55 MPa√m. (NOTE: Y=1.12 for edge crack and use “a” not “2a” for the length of the crack) 1. At the given crack size and tensile loading would the rod undergo instantaneous fast fracture, assuming plane strain conditions? Show calculations to back up your conclusions.
A tie rod made of quenched and tempered 4340 steel is used as a critical linkage in an industrial apparatus. The rod is subjected to an alternating cyclic tensile/compressive stress from 550 MPa to -550 MPa. An inspection of the rod revealed a 3.5 mm deep edge crack on the surface of the rod. Please answer the following question for the rod given the properties in the table and curve below and fracture toughness of 55 MPa√m. (NOTE: Y=1.12 for edge crack and use “a” not “2a” for the length of the crack) 1. What is the minimum crack size that would cause instantaneous fast fracture at the current maximum axial tensile loading, assuming plane strain conditions apply? If the resolution limit of the flaw detection apparatus were 1.5 mm, would this flaw be subject to detection? Show calculations to back up your conclusions.
A tie rod made of quenched and tempered 4340 steel is used as a critical linkage in an industrial apparatus. The rod is subjected to an alternating cyclic tensile/compressive stress from 550 MPa to -550 MPa. An inspection of the rod revealed a 3.5 mm deep edge crack on the surface of the rod. Please answer the following question for the rod given the properties in the table and curve below and fracture toughness of 55 MPa√m. (NOTE: Y=1.12 for edge crack and use “a” not “2a” for the length of the crack) 1. Given the S-N curve for 4340 steel, is there an endurance limit? If so, what is the stress value for the endurance limit? 2. If there were no cracks and the stress on the rod still alternated from 550 MPa to -550 MPa with mean stress of zero, what would be the cycles to failure?
Tensile and fully reversed loading fatigue tests were conducted for a certain steelalloy and revealed the tensile strength and endurance limit to be 1200 and 550 MPa,respectively. If a rod of this material supply were subjected to a static stress of 600MPa and fully-reversed oscillating stresses whose total range was 700 MPa. Assuming garber relationship will this rod fail by fatigue failure
The top lid of a nuclear reactor is being held by clamping screws which are made of AISI 4340 steel tempered at 260°C. They are stressed to a maximum level of 1050 MPa during a pressurization test before starting the reactor. Find the factor of safety guarding against yielding and the factor of safety guarding against crack propagation if the initial cracks in the material have B=1.3 and a=1.2 mm