A sample coarse grained soil is 50mm. In diameter and 150mm long was tested in a constant-head apparatus. The soil sample was prepared at a void ratio of 1.5. The total head was kept constant at 300mm and the amount of water is collected in 4 sec. was 50cm^3. The test temperature was 22°C a.) Compute the temperature correction factor. b.) Compute the corrected coefficient of permeability in cm/sec. c.) Compute the interstitial velocity.

A sample coarse grained soil is 50mm. In diameter and 150mm long was tested in a constant-head apparatus. The soil sample was prepared at a void ratio of 1.5. The total head was kept constant at 300mm and the amount of water is collected in 4 sec. was 50cm^3. The test temperature was 22°C a.) Compute the temperature correction factor. b.) Compute the corrected coefficient of permeability in cm/sec. c.) Compute the interstitial velocity.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter3: Weight–volume Relationships

Section: Chapter Questions

Problem 3.5P

See similar textbooks

Similar questions

please solve B only. subject: geotechnical Engineering A sample coarse grained soil is 50mm. In diameter and 150mm long was tested in a constant-head apparatus. The soil sample was prepared at a void ratio of 1.5. The total head was kept constant at 300mm and the amount of water is collected in 4 sec. was 50cm^3. The test temperature was 22°Ca.) Compute the temperature correction factor.b.) Compute the corrected coefficient of permeability in cm/sec. c.) Compute the interstitial velocity.
In a falling head permeameter, tge sample used is 18cm long havibg a cross sectional area of 22cm^2. The sample of soil is mqde of three layers. The thickness of the first layer from the top is 8cm and has a value of k1=4x10^-4 cm/sec, the second layer of thickness 8cm has k2=5.5x10^-4 cm/sec and the bottom later of thickness 4 cm has k3=7x10^-4 cm/sec. Assume that the flow is taking place perpendicular to the layers. The cross sectional area of the stand pipe is 3cm^2. A.Calculate the equivalent coefficient permeability in cm/sec of the soils ib tye direction of the flow Choices: 4.44 x10^-4 cm/s 4.97x10^-4 cm/s 3.24x10^-4 cm/s 3 53x10^-4 cm/s B.Calculate the flow rate in cm^3/hr when the head drops from 25cm to 12cm Choices: 18.20,24.58,28.42,20.65 C.Calculate the time recquired for a drop of head from 25 cm to 12 cm Choices: 58.22,62.91,97.05,60.44
during a subsurface exploration, an undiscovered soil sample was collected from the field using a split spoon sampler for lab evaluation. the sample has a diameter of 34.9mm length of 457.2mm and a moist mass of 840g. if the oven dried mass was 680g and Gs= 2.74 calculate the ff. a.)moist unit weight b.)moisture content c.)dry unit weight d.)void ratio e.)degree of saturation
FUNDAMENTALS OF GEOTECHNICAL ANALYSIS A constant head permeability test is performed on soil that is 2 cm x 2 cm square, and 2.5cm long. The head difference applied during the test is 20 cm and 7 cm3 is collected over a time of 100 sec. a) Compute the permeability based on these test conditions and results. b) A falling head test is conducted on the same soil specimen at the same time (t1 – t2 = 100 sec), and the standpipe diameter is 0.8 cm. If the average head during the test should be 18 cm, what are h1 and h2 values?
A constant head permeability test has a soil sample length in the direction of flow of 350 mm, a sample cross sectional area normal to the flow direction of 125 cm2, and a head loss through the sample of 420 mm. The soil sample is a medium dense sand with a void ratio of 0.61. During a 3 minute test period, 580 cm3 of water flowed through the sample. (a) Sketch the Constant Head Permeameter and label the sketch with the appropriate dimensions given above. (b) Determine the Hydraulic conductivity, k, in cm/sec, and the seepage velocity (not just apparent velocity).
A soil sample has a maximum void ratio of 0.95 and minimum void ratio of 0.55. It was also found out that the porosity is 25%, moisture content is 16% and Gs = 2.65. Compute the dry unit weight of the sample.a. 16.45 kN/m^3b. 17.53 kN/m^3c. 19.50 kN/m^3d. 20.02 kN/m^3
2. Sand cone equipment is used to perform a field density test on a compacted earth fill. Sand is used in the cone and is known to have a bulk density of 15.74 kN/m3 . Soil sample dug from test hole, (wet weight) = 20.601 N Dry weight of soil sample = 17.926 N Weight of sand (sand cone) to fill test hole = 16.503 N Determine the in-place dry density of the tested soil (Ans: 17.57 kN/m3) Determine the water content (Ans: 15%) Compute the percentage of compaction of the tested soil if the laboratory moisture-density curve indicates a dry density of 18.10 kN/m3 and an optimum moisture content of 13%. (Ans: 97.07%)
Subject: Soil Mechanics Provide solution and diagram. A direct shear test, when conducted on a remolded sample of sand, gave the following observations at the time of failure: Normal load = 288 N; shear load = 173 N. The cross-sectional area of the sample = 36 cm2. Determine the angle of internal friction in degrees. a. 29 b. 27 c. 31 d. 33
A soil sample is 15mm thick, has an original void ratio of 0.95, if the coid ratio is decreased to 1/4 of its orginal void ratio, what would be its new thickness? choices: a) 5.48mm b) 9.52 mm c) 11.35 mm d)3.65mm