A sand deposit contains three distinct horizontal layers of equal thickness. The hydraulic conductivity of the upper and lower layers is 10-3 cm/sec and that of the middle is 10-2 cm/sec. What are the equivalent values of the horizontal and vertical hydraulic conductivities of the three layers, and what is their ratio?

A sand deposit contains three distinct horizontal layers of equal thickness. The hydraulic conductivity of the upper and lower layers is 10-3 cm/sec and that of the middle is 10-2 cm/sec. What are the equivalent values of the horizontal and vertical hydraulic conductivities of the three layers, and what is their ratio?

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter2: Geotechnical Properties Of Soil

Section: Chapter Questions

Problem 2.11P

See similar textbooks

Similar questions

A sand has Gs = 2.66. Calculate the hydraulic gradient that will cause boiling for e = 0.35, 0.45, 0.55, 0.7, and 0.8.
For a constant head permeability test in a sand, the following values are given:• L 350 mm• A 125 cm2• h 420 mm• Water collected in 3 min 580 cm3• Void ratio of sand 0.61Determine:a. Hydraulic conductivity, k (cm/sec)b. Seepage velocity
The hydraulic conductivity of a soil sample is 0.01 cm/sec at void ratio of 0.8. What will be the hydraulic conductivity of the same sample at void ratio of 1.
For a sandy soil, the following are given: • Maximum void ratio = 0.72 • Minimum void ratio = 0.46 • Hydraulic conductivity at a relative density of 80% = 0.006 cm/sec. Determine the hydraulic conductivity of the sand at a relative density of 67%.
From the figure shown, the void ratio of the sand is 0.55 with a specific gravity of 2.68. The cross-sectional area of the tank is 0.5 sq.m and hydraulic conductivity of sand = 0.1 cm/s. a. What is the rate of upward seepage in cu.m/hour? b.Determine the critical hydraulic gradient for zero effective stress. c. Determine the value of h (head loss) to cause boiling. NEED ASAP. THANK YOU.
The hydraulic conductivity of a sand at a void ratio of 0.750 is 0.047 cm/s. Estimate the coefficient of permeability at a void ratio of 0.450 1. Using Casagrande equation 2. Using Kozeny-Carman equation
A sample of sand is subjected to a constant head permeability test. The sample diameter is 60 mm and its length is 130 mm. Under an applied head of 60 cm, 119 cm³ of water flows through the sample in 5 minutes. Determine (a) the coefficient of permeability, and (b) the discharge velocity.
For a laboratory consolidation test on a clay specimen (drained on both sides) the following results were obtained: Thickness of clay soil= 25 mm; P_1 = 50 kPa; P_2 = 120 kPa; e_1 = 0.92; e_2 = 0.78; Time for 50% consolidation= 2.5 min. Tv = 0.197. Determine the hydraulic conductivity of the clay for the loading range in m/min. Show diagram
2. Situation 2 - For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen = 16 cm Diameter of specimen = 96 mm Constant Head Difference = 50 cm Volume of water collected in 4 min = 420 cc Void ratio of the soil specimen = 0.55 a. Determine the hydraulic conductivity of the soil in m/min. Round off to four decimal places. b. Determine the discharge velocity in m/min. Round off to four decimal places. c. Determine the seepage velocity in m/min. Round off to four decimal places.
Experimental data for clay specimen obtained initial values of e1 = 1.12 and P1 = 90 kPa, and final values of e2 = 0.90 and P2 = 460 kPa What is the hydraulic conductivity in cm/s if the coefficient of consolidation is 0.036 cm2/s
For a normally consolidated laboratory clay specimen drained on both sides, the following are given: σ0’ = 4000 ib/ft² e=1.2 σ0’ + Δσ’= 5000 lb/ft² e=0.9 Thickness of clay specimen= 2in Time for 50% consolidation= 2 min. Determine the hydraulic conductivity (ft/min) of the clay for the loading range. How long (in days) will it take for a 6-ft clay layer in the field(drained on both side) To reach 60% consolidation?
The results of a constant-head permeability test for a fine sand sample having a diameter of 150 mm and a length of 300 mm are as follows • Constant-head difference = 500 mm • Water collected in 5 min = 350 cm3 • Void ratio of sand = 0.61 Determine: a. Hydraulic conductivity, k (cm/sec) b. Seepage velocity