A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. (use Perry's Handbook for the properties and constants) R = 8314J/kg mol K; MW=18.02g/mol a. What is the value of G in kg/s.m2? b. What is the value of friction factor? c. What is the % of pressure drop? d. Calculate the outlet pressure.

A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. (use Perry's Handbook for the properties and constants) R = 8314J/kg mol K; MW=18.02g/mol a. What is the value of G in kg/s.m2? b. What is the value of friction factor? c. What is the % of pressure drop? d. Calculate the outlet pressure.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

a steel pipe has an inside diameter of 25 mm, is 20 m long, and carries 10 deg Celcius water at a rate of 4.5 m^3/h. at this rate, the friction factor of the pipe is 0.0259. If the pressure at the inlet is 70 kPa, what is the static pressure of the water at the outlet.
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
Water at 940 kPakPa , 25∘C∘C enters a 1-mm-diameter horizontal pipe with a steady velocity of 19 m/sm/s . At the exit the pressure drops to 860 kPakPa due to viscous resistance. Assuming steady-state flow, determine the rate of heat transfer (Q˙Q˙) necessary to maintain a constant specific internal energy (uu).
In the figure, the cylindrical capacitor, connected to a constant voltage source Vo= 80 V, rests with its edges on the surface of the water of density ρ=1000 kg/m3 . The distance d=0.4 cm between the condenser armatures is much smaller than its radius half. Find the height "h" at which the water level is established between the reinforcements of the condenser. Neglect capillary phenomena. (k=9•109N•m2/C2,κ=81,g=9.8m/2)
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the value of G in kg/s.m2?. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol What is the a.) value of G in kg/s.m2? b.)value of friction factor? 3 significant figures c.)the % of pressure drop? d.)the outlet pressure? e.) compressible or not?
If 1 cubic meter of water at 0°C is frozen and cooled to -8 degree Celsius by being in contact with a great deal of ice at -8 degree Celsius, estimate the total change in entropy of the process. Given : Required : Illustration: Solution: final answer:
14. Through a refinery, fuel ethanol is flowing in a pipe at a velocity of 1 m/s and a pressure of 101300 Pa. The refinery needs the ethanol to be at a pressure of 2 atm (202600 Pa) on a lower level. How far must the pipe drop in height in order to achieve this pressure? Assume the velocity does not change. (Hint: Use the Bernoulli equation. The density of ethanol is 789 kg/m3 and gravity g is 9.8 m/s2
Here, air (105 kPa) at 37 degrees celcius is flowing upward in a 6cm diamater inclined duct, at a rate of 90 L/s. In this case the density of air is 1.1 kg/m3. The diameter of the duct reduces to 4cm through a reducer and a pressure charge occurs. This pressure change is measured by a water manometer. The elevation difference between the points where the two arms of the manometer are attached is 0.2 meters. What is the differential height between the fluid levels in the two manometer arms?
Water at 20°C flows in a 100-mm-diameter new cast iron pipe with a velocity of 5.0 m/s. Determine thepressure drop in kPa per 100 m of pipe and the power lost (in kilowatts) to friction.Ans. 314 kPa per 100 m, 12.36 kW per 100 m [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based on temperature available on the internet. E.g. (density, viscosity) . Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness}
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. It will under compressible or incompressible criteria. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
Water at four-degree Celsius flows through a pipe that has a conical shape and is sloping downward; has a height difference of 20 meters. The cross section at the bottom is one-half that at the top. If the speed and pressure of water at the top are 1 m/s and 3x105 Pa, what is the pressure at the bottom (20 meters below the top)?