A SERIES CIRCUIT CONTAINING A 30OHMS RESISTOR AND 40 OHMSINDUCTIVE REACTANCE ISCONNECTED TO A 240 V SOURCE,60HZ LINE. (Answer: Item 11-20)12. The total current of the13. The voltage drop across the11. The total impedance of thecircuit is: *resitor is: *circuit is: *O A. 3.5 AO A. 148 VA. 50 ohmsB. 123 VO B. 4.8 AB. 40 ohmsO C. 144 VO C. 20 ohmsO C. 5.2 AO D. 156 VD. 60 ohmsO D. 3.6 A

Answered: Image /qna-images/answer/b9867610-3bf8-44e1-8b07-9c2269eec441.jpg

A SERIES CIRCUIT CONTAINING A 30 OHMS RESISTOR AND 40 OHMS INDUCTIVE REACTANCE IS CONNECTED TO A 240 V SOURCE, 60HZ LINE. (Answer: Item 11-20) 12. The total current of the 13. The voltage drop across the 1. The total impedance of the circuit is: * resitor is: * circuit is:* O A. 148 V A. 3.5 A O A. 50 ohms B. 123 V O B. 40 ohms О в. 4.8 А О с 14 V О с.20 ohms O C.5.2 A O D. 156 V O D. 60 ohms O D. 3.6 A

A SERIES CIRCUIT CONTAINING A 30 OHMS RESISTOR AND 40 OHMS INDUCTIVE REACTANCE IS CONNECTED TO A 240 V SOURCE, 60HZ LINE. (Answer: Item 11-20) 12. The total current of the 13. The voltage drop across the 1. The total impedance of the circuit is: * resitor is: * circuit is:* O A. 148 V A. 3.5 A O A. 50 ohms B. 123 V O B. 40 ohms О в. 4.8 А О с 14 V О с.20 ohms O C.5.2 A O D. 156 V O D. 60 ohms O D. 3.6 A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter8: Combination Circuits

Section: Chapter Questions

Problem 4PA: The hot water for the heating system for a small factory is supplied by a single boiler. The bolier...

See similar textbooks

Similar questions

d.1. What are the two concepts that make up grounding in its simplest form?A. Impedance and resistanceB. System grounding and equipment groundingC. DC systems and AC systemsD. Grounded and ungroundedd.2. Which of the following types of grounding electrodes was one of the first grounding electrodes to berequired for use?A. Ground ringB. Water pipeC. Concrete-encasedD. Rod and piped.3. What is the primary purpose of the National Electrical Code?A. To serve as a training manual for untrained personsB. To provide design specifications to professionalsC. To act as a collection of procedures for electriciansD. To safeguard against electrical hazards
Show all steps and working please.You have been privately contacted to rewire a site. During a visit, you observed that the building receives a 400V, 60Hz, star-connected, three-phase supply from the utility. There are also several three-phase equipment that require a 230V three-phase supply. You have decided to utilize three single-phase, dry type transformers to step down the building’s incoming supply to a 230V, delta-connected supply for the equipment. All the three-phase machinery can be modelled as an equivalent balanced three-phase star-connected load with a resistance and inductance of 0.5Ω and 0.16mH respectively per phase. Some preliminary calculations and analysis are required before starting the wiring design. Discuss two (2) advantages and disadvantages of using three single-phase transformers instead of a composite three-phase transformer?
Show all steps and working please.You have been privately contacted to rewire a site. During a visit, you observed that the building receives a 400V, 60Hz, star-connected, three-phase supply from the utility. There are also several three-phase equipment that require a 230V three-phase supply. You have decided to utilize three single-phase, dry type transformers to step down the building’s incoming supply to a 230V, delta-connected supply for the equipment. All the three-phase machinery can be modelled as an equivalent balanced three-phase star-connected load with a resistance and inductance of 0.5Ω and 0.16mH respectively per phase. Some preliminary calculations and analysis are required before starting the wiring design. Assuming the transformer is ideal and lossless and that all neutrals are grounded, calculate:i)The phase voltages of the star-connected load.ii)The line currents between the transformer and loadiii)The phase currents in the transformer secondary windingsiv)The total…
three transformers connected as indicated below to step the voltage down from 13,200V to 460V. a) determine the ratio of the transformer if the transformers are connected wye-delta. b) determine the ratio transformation if the transformers are connected wye-delta. c) determine the ratio of transformation if the transformers are connected delta-wye. d) determine the ratio of the transformation if the transformers are connected delta-delta. BOX THE FINAL ANSWER AND USE 4-5 DECIMAL PLACES FOR THE ANSWER subject: ELECTRICAL APPARATUS AND DEVICES
The hot water for the heating system for a small factory is supplied by a single boiler. The bolier is locatd in a small building separate form the factory. The power supplied to the bioler is 240-volt single-phase without a netural conductor. At the present time, the small building housing the bioler has no inside lighting. The business owner desires that four 100-watt lamps be installed inside the building. All lamps are to be connected to a single switch. The lamps are to be connected to the present 240-volt sercvice inside the building. How would you accomplish this task? Explain your answer.
3. What is the impedance of the circuit in Question 2?
g.1. The Let-Go current threshold for people has defined the operating point for a Class A GFCI receptacleto be _______ mA.A. 15–20B. 4–6End of examC. 6–10D. 10–12g.2. The amount of current in each separate conductive path is related to the _______ in each of the pathsinvolved.A. fuse time-current curveB. interrupting ratingC. reactanceD. impedanceg.3. In an AC circuit, the total opposition to the flow of current that's offered by the combination of theresistance, the capacitive reactance, and the inductive reactance is called theA. impedance.B. voltage reactance.C. electrostatic reactance.D. total inductive reactance.
HEY, PLEASE REPLY AS SOON AS POSIBLE. 1) For the circuit in Figure, what is the value of RN between terminals a and b, in Ω? Questions 11 and 12 refer to this same circuit? 2) For the circuit of Figure 3, what is the value of iN between terminals a and b, at Amps? 3) What should be the value of a resistor connected between and b if you want it to consume the maximum possible power?
Part i ii and iii have been already answered. Please show steps to obtain part iv only. i have attatched parts i to iii. You have been privately contacted to rewire a site. During a visit, you observed that the building receives a 400V, 60Hz, star-connected, three-phase supply from the utility. There are also several three-phase equipment that require a 230V three-phase supply. You have decided to utilize three single-phase, dry type transformers to step down the building’s incoming supply to a 230V, delta-connected supply for the equipment. All the three-phase machinery can be modelled as an equivalent balanced three-phase star-connected load with a resistance and inductance of 0.5Ω and 0.16mH respectively per phase. Some preliminary calculations and analysis are required before starting the wiring design. Assuming the transformer is ideal and lossless and that all neutrals are grounded, calculate:i)The phase voltages of the star-connected load.ii)The line currents between the…
Please give the correct solution with neat and clean formatting For the series-parallel arrangement shown in Figure, determine the equivalent series circuit impedance, the supply current I, the circuit phase angle, the values of voltages V1 and V2, and the values of currents IA and IB
Four single-phase circuits. Each circuit is rated 50A and 230 Volts. The length ofthe circuits is 32m. The circuits are protected by 50A BS 88-2 fuses. Thesecircuits are supplied by two-core cables of 25 mm² using Reference Method B.Part of the circuits will be through an area where the ambient temperatura is35◦C. The earth loop impedance external to the installation Ze = 0.3 Ω. Theoperating temperature is 70◦C and the c.p.c. conductor cross-sectional area is 10mm².Determine:a) The ambient temperature factor (Ca) and the grouping factor (Cg) and thetabulated current It.b) The voltage drop if the power factor of the load is 0.8 lagging.c) Check the validity of the circuits for shock-risk.d) Check the validity of the circuits for the let-through energy.e) The maximum length permissible for each circuit.
1. A 10 kVA, 440/110 V, two-winding transformer is reconnected as a step-down 550/440 V autotransformer. Determine (a) current in the common winding, (b) new kVA rating as an autotransformer and (c) power conductively transferred. BOX THE FINAL ANSWER Subject: Electrical Apparatus and Divices