The following 5 signals are to be sampled at the Nyquist rate.and multiplexed and transmitted by the means of TDMX,(t) band-limited to 2.5kHzX2(t) band-limited to 2.5kHzXa(t) band-limited to 10kHzX4(t) = sin 5000 7tX5(t) band limited to 5kHzThe output of the multiplexer is uniformly quantized with L=1024 and binary encodedA) setup a scheme for accomplishing this multiplexingrequirementB) what must be the speed of the commutator (in sample per?second )?C) what is the output bit rateD) what is the minimum transmission bandwidth of the? channel

“Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Answered: A) setup a scheme for accomplishing…

A) setup a scheme for accomplishing this multiplexing requirement B) what must be the speed of the commutator (in sample per ?second) ?C) what is the output bit rate

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Describe the costs and benefits of aliasing, and explain how it can be avoided

Q: An a differential pulse code modulated system, the transmitted bits per sample is 7. How many…

A: number of quantization level given by 2nwhere n is no of bits

Q: QA: what is Encoders and Decoders

A: The explanation is as follows.

Q: In time the use of the important parameter of the equivalent circuit was determined by the actual…

Q: What does a binary digital signal consist of?

Q: Decoder circuit as shown in the following Figure. if A is LSB and C is MSB, the output expression F=

Q: What is the processing gain in a DSSS system with a 1.5-MHz channel and a data rate of 20 kbps?

A: In Direct sequence spread spectrum the pseudorandom code which occurs at fast rate can increases the…

Q: B. Write a VHDL code for designing (2-to-1) 1-bit Multiplexer using an TI statement.

A: Let input to mux are i0,i1 Select line is s Output y

Q: Why does base bias produce such an unstable Q point?

A: According to the question we have to discuss, why does base bias produce such an unstable Q point?

Q: Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted…

A: We need to find out the number of bits per sample and data rate for given pcm signal

Q: 1. What is the difference between synchronous binary counter and asynchronous binary counter?

A: Note:Dear student here you have posted multiple question in sigle request.We will solve first…

Q: Design a 4-bit up/down gray counter?

Q: Q1: Plot a BPSK signal for the bit stream data 1010101101, assume that the frequency of signal is…

Q: 17.1 What are the keys to a successful mixed-signal PCB layout?

A: Types of PCB Single layer PCB Multi Layer PCB High frequency PCB Double layer PCB HDI layer PCB…

Q: Q3) A baseband signal varies between -2 and 12 Volts is to be transformed to binary digital form,…

A: Bit rate Rb=n fs 56 kb=n14 KHz n=4 bits(a) No of quantisation levels = 2n=24=16 levels

Q: Design a 3Bit Odd Parity Detector using :a) Multiplexer b) Decoder, and appropriate gates?

A: To design a 3 bit odd parity detector, we will use 3 bits A, B, C & output will be Y Therefore…

Q: What is the difference between synchror binary counter and asynchronous binary counter?

A: Counters can be classified into two typed based on how clock signal is applied.

Q: Specifically describe in a real world application scenario how virtualization is different from…

A: Networking- In technological term A network is a collection of computers, servers and other devices…

Q: Explain information regarding Discrete Signal

A: A discrete sign or discrete-time signal is a period series comprising of a grouping of amounts.…

Q: over the sampling (Nyquist) rate. Suppose it used 0.5% as a maximum quantization level error with…

Q: For binary pcm, if 7 is the number of bits per sample, then what will be signal to quantization…

A: Given information: The number of bits per sample is given as v=7

Q: What is the probability of error with a PSK system with a bit rate of 20kpbs, BW of 50 kHz, Noise…

A: The solution is given below

Q: The figure below shows a multiplexer where S, and S, are the select lines. I, to I, are the input…

A: Using K-map to solve the expression, we get

Q: Contrast the advantages and disadvantages of digital transmission.

A: Advantages of digital transmission are, It provides immunity towards the noise. These signals are…

Q: are specifications of Digital modulation techniques?

A: Digital Modulation Techniques. It is the kind of process in which encode a digital information…

Q: 4) Illustrate the generation of noncoherent version of PSK signal for the input binary sequence…

A: Non-coherent PSK Generation : Initially, we are giving the input binary stream and delayed output…

Q: Q4: Show how to PSK modulate and demodulate the data sequence (01101). Assign two full cycles of…

A: 4. Given, PSK modulator has Input data sequence = 01101 Number of cycles of carrier for each data…

Q: In a digital communication, explain all the methods/mechanism used for the minimization of Bit Error…

A: The methods which are used for minimisation of Bit Error rate is as follows: WDFE beneficiaries got…

Q: Q4. Consider the QPSK digital modulation scheme (a) What does the abbreviation QPSK stand for? (b)…

Q: What will be the minimum transmission bandwidth of a PCM system if the number of bits per sample is…

A: Given information: The maximum frequency component present in the analog input signal is fm=4.5 kHz.…

Q: Q4. Consider the rectangular 16-QAM (quadrature amplitude modulation) digital modulation scheme (a)…

A: (a) Hence we have the constellation diagram as :

Q: What are the functions of encoder, Decoder, multiplexers explain with truth table and give…

A: FUNCTION OF ENCODER: It is a circuit that is used to convert the given data from one format to…

Q: In a PCM system, the maximum frequency of the analog input signal is 4 kHz. If the number of…

A: Given that Maximum frequency of the analog input signal (fm) = 4 kHz Quantization level=2 =2n So…

Q: Give detailed information about Nyquist-Nyquist–Shannon sampling theorem. Explain what Aliasing is…

A: Give detailed information about Nyquist –Shannon sampling theorem. Explain what Aliasing is in…

Q: c) (i) i. Describe the precaution you would take in selecting the sampling interval ii. How may the…

A: (i) Precaution in selecting the sampling interval, The main precaution is that the sampling…

Q: 4000 Hz, what sampling rate should be used to retain all necessary information in the digital data?…

Q: HW 3 What is aliasing phenomenon, and what is it's effect on the data recovery in DCS, show how can…

A: Aliasing phenomenon that occurs during the improper sampling process. It is also the process of…

Q: What is difference between * ?Decoder and Encoder

A: Encoder: The encoder circuit is introduced at the communicating end.An Encoder is a gadget that…

Q: Consider error control methods in digital signal transmission. Assume Hamming code is used with even…

Q: what is Successive approximation ADC? please explain

A: Here is block diagram of SAR. It uses Bisection method to keep or alter the bit for set or reset.…

Q: explain the aliasing in the PAM Signal?

A: The analog pulse modulation techniques are classified into three types, which are mentioned as…

Q: What is the main disadvantage of linear delta modulation? What is the solution for this problem?…

A: There are generally two disadvantages of linear delta modulation, and these are in step-2.

Q: 4. How to use the PLL circuit and the logic circuit to comprise a doubler frequency circuit?

A: PLL circuit : PLL circuit is known as phase locked loop circuit it is an electronic circuit which is…

Q: Describe the purpose of multiplexing in an explain the advantages of multiplexing. optical…

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again. The…

Q: What is difference between ?Decoder and Encoder

A: Encoder: An Encoder is a gadget that changes over the dynamic information signal into a coded…

Q: or the multiplexer circuit shown in Figure below. is performed by these multiplexers?

Question

The following 5 signals are to be sampled at the Nyquist rate
.and multiplexed and transmitted by the means of TDM
X,(t) band-limited to 2.5kHz
X2(t) band-limited to 2.5kHz
Xa(t) band-limited to 10kHz
X4(t) = sin 5000 7t
X5(t) band limited to 5kHz
The output of the multiplexer is uniformly quantized with L=
1024 and binary encoded
A) setup a scheme for accomplishing this multiplexing
requirement
B) what must be the speed of the commutator (in sample per
?second )
?C) what is the output bit rate
D) what is the minimum transmission bandwidth of the
? channel

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1-v(t) = 8cos(2π x160t)+ 4cos(2π x640t) A- Calculate the Nyquist rate for this signal? B- If v(t) is sampled at a rate Ts = 0.001 s what is the resulting discrete time signal v(n)? 2- repeat the Q2 for above v(t) 3- assuming that a3 bit ADC channel accepts analog input 0 to 5 volts, determine A- the no. of quantization levels B- the step size of the quantize C- the quantize level when the analog voltage is 3.2 v D- the binary code produced by the ADC
6/ A TV signal has a bandwidth of 4.5 MHz. The signal is sampled according to the Nyquist theorem, quantized in 1024 levels and coded to obtain a PCM signal. Nyquist theorem, quantized in 1024 levels and encoded to obtain a PCM signal, which is then transmitted using a 16-PAM scheme. transmitted using a 16-PAM scheme. What is the transmission rate in baud [symbols/second]? [symbols/second]?
Classify the transfer function to proper and improper. Plot the s-plane and find the system stability.
A voice signal (which extends from 300HZ to 3333HZ in the frequency domain) is digitized by 32 levels PCM. The sampling rate is set to be 120% over the Nyquist rate. Find: (1) the maximum SNqR, (2) the output data bit rate, (3) the required bandwidth of the channel
A telephone signal with a cut-off frequency of 4 kHz is digitized into 8-bit PCM, sampled at Nyquist rate. Calculate the baseband transmission bandwidth and quantization S/N ratio.
Solve the following, if a television signal (video and audio) has a bandwidth of 4.5 MHz. This signal is sampled, quantized, and binary coded to obtain a PCM signal.I. Find the sampling rate if the signal is to be sampled at a rate of 20% above the Nyquist rateII. If the samples are quantized into 2048 levels, determine the number of binary pulses required to encode each sampleIll. Determine the binary pulse rate (bits per second) of the binary-coded signal, (or ) the minimum bandwidth required to transmit this signallV. Find the channel capacity using the Nyquist rule.
How would you do this? I know in order to find stabitly we need to find its transfer function but how would we do that? Whats Vin and Vout in this case? what would you recommend?
A digital communication link carries binary-coded words representing samples of an input signal, xa(t)=3cos⁡(600πt)+2cos⁡(1800πt)The link is operated at 1,000 samples/s. (a) What is the folding frequency? (b) What is the Nyquist rate for the signal xa(t)? (c) What are the frequencies in the resulting discrete-time signal x(n)? (d) Will there be any aliasing here? (e) Which frequency will alias to what frequency
Calculate the following with the assumption that an audio signal uses PCM with a bandwidth of 15 kHz and signal levels are 65536. Find the Nyquist rate. Find the number of binary digits required to encode a sample. find the number of binary digits per second (bit/s) required to encode the above signal.
A television signal (video and audio) has a bandwidth of 4.5 MHz. The signal is sampled, quantized and binary coded to obtain a Pulse Coded Modulated (PCM) signal. (a) Determine the sampling rate if the signal is to be sampled at a rate of 20% above the Nyquist rate.(b) If the samples are quantized into 1024 levels, determine number of binary pulses (or digits) required to encode each sample.(c) Determine the binary pulse rate (bits per second) of the binary coded signal.(d) Calculate minimum bandwidth required to transmit this signal.
HM: Design the following circuit using a Decoder F= l_[(o,6,7,8,11,13.14,15)
Evaluate the discrete-time convolution sums given below. Also, obtain the same result usingDTFT(i.e., DTFT and then inverse DTFT) for both cases. a)y[n]=u[n+3]∗u[n−3] b)x[n]=u[n]−u[n−2], h[n]=(0.5)nu[n] this is a signal systems question