: A shaft ABCD, 25 mm in diameter is subjected to torques of 1850 N-m at B and 2000 N-m at C acting in the same direction. Segment AB is 4 m long, BC is 2 m long, and CD is 4 m long. Supports A and D are fixed and unyielding. G = 86 GPa. A. Reaction at A (N-m) B. At what segment is the torsional stress largest? What is the stress on that segment? (MPa) C. Angle of rotation between points A and C (radians)

: A shaft ABCD, 25 mm in diameter is subjected to torques of 1850 N-m at B and 2000 N-m at C acting in the same direction. Segment AB is 4 m long, BC is 2 m long, and CD is 4 m long. Supports A and D are fixed and unyielding. G = 86 GPa. A. Reaction at A (N-m) B. At what segment is the torsional stress largest? What is the stress on that segment? (MPa) C. Angle of rotation between points A and C (radians)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum absolute bending strain in the following tubular shaft if di = 160 mm and do = 200 mm. (E = 154 GPa)
The steel shaft DF consists of three concentric tubes and is supported by smooth bearings at D and E. It is coupled to a motor at F, which delivers 15 kW of power to the shaft while it is running at 55 rev/ sec. The gears A, B, and C remove 4 kW, 5 kW, and 6 kW, respectively. The shaft is free to turn in its support bearings D and F. Determine the shearing stress developed in segments BC and CE
the ladder has a uniform weight of 80lb and rests against the wall at B. if the coefficient of static friction at A and B is 0.40. A.) determine the normal force at B in lb. B.) determine the normal force at A in lb.
Determine the tension at calble AB and force F in the loading system below for equilibrium.
F=1.7 kN W= 11.1 kN/m Find the reaction force and moment at support A Find the maximum absolute bending stress
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
The solid circular shaft is subjected to an internal torque of T= 6.0 kN.m. Determine the shear stress developed at point A and B
Which of the following is the nearest value for the force at member BC? a. 5kN tension b. 1.6 kN tension c. 1.6 kN compression d. 5 kN compression
A uniform load of 112kN/m is acting downward and supported by an upward uniform pressure of q = 48kN/m. Determine the following: 1. Maximum moment 2. Maximum shear 3. Distance from the left where the flexural stress is zero.
A sluice gate in the wall of a dry dock is 1.83 m square and is hinged at the top. The gate opens into the dock and when the dock is filled with sea water, the water level is 0.915 m above the hinge. Calculate the force on the rubber joint at the bottom of the gate, and reaction at the hinge. Solve using fluid statics method Ans. 35.9 kN, 25.6 kN
The homogeneous bar AB weighs 400 N. End B leans against a frictionless vertical wall and end A is supported by a ball-and-socket joint. 1. Determine the tension in cable BC. 2. Determine the wall reaction at B. 3. Determine the total reaction at A.
In the beam shown, take P1 = 4 kN, P2 = 7 kN, and W1 = 5 kN/m. b) Determine the vertical reaction at "B"