A shaker-type baghouse is to be designed to remove gypsum dust from a wall-board manufacturing plant exhaust gas stream flowing at 125,000 adxo. The air stream is at 175 °F and has a signilicanfc content of SO2 gas, Specify, the total number of bags, assuming each bag has 35 ft2 of cloth area, (Be sure to consider a proper layout of bags in each compartment),

A shaker-type baghouse is to be designed to remove gypsum dust from a wall-board manufacturing plant exhaust gas stream flowing at 125,000 adxo. The air stream is at 175 °F and has a signilicanfc content of SO2 gas, Specify, the total number of bags, assuming each bag has 35 ft2 of cloth area, (Be sure to consider a proper layout of bags in each compartment),

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.21P

See similar textbooks

Similar questions

Problem :3 only (category: friction factor, FE prep): Air at 1 atm and 10°C flows in a 4 cm diameter glass pipe (roughness of 0) at a velocity of 7 m/s. Find the friction factor. Calculate the head loss over a 2 m length of pipe. Air at 1 atm and 10°C has kinematic viscosity of 1.087 x 10-5
A pulse-jet baghouse is desired for a finished cement plant. Calculate the number of bags required to filter 500 m3/min of air with a dust loading of 3,0 g/m3. Each bag is 3.0 m long with a 0.13 m diameter. If the average pressure drop is 1.0 kPa and the main fan is 80% efficient, calculate the fan power in kW< If the pulse air volumetric flow rate is 0.5% of the filter airflow rate and the pulse air pressure is 6.0 atm, calculate the power drawn by a 50% efficient compressor (in kW).
A venturi scrubber operates such that Nt =(PT)1/2. At a power input of 4 hp/1000 cfm and an Inlet dust loading of 1.5 gr/ft2 what is the outlet loading?
Medium fuel oil having an absolute viscosity of 6.55 x 10⁻⁵ ft²/s flows in a steel pipe 4100 ft long at a maximum rate of 0.201 cfs. Which of the following most nearly gives the minimum diameter of the pipe in ft required to keep the flow in a laminar condition?
Solve for what is being required. Room dimensions are: LxWxH = 8.50 m, 5.0 m, 3m. Originally, the room had linoleum flooring with an absorption coefficient of 0.03. Two opposite walls were cladded with unglazed bricks with an absorption coefficient of 0.02, the one having the entrance gypsum door (2.1 m X 0.80 m) with 0.05 abs.co.; the other two were just bare concrete with sliding glass window openings of 1.80m x 1.20 m each; the bare concrete with an abs.co. Of 0.31 and the window glass with 0.18, the ceiling, too , had bare concrete as its finish at 500 Hz. The client would like to renovate the space into an acoustical studio room and would like to change the ceiling and the flooring. The ceiling will have a vinyl faced fiberglass panel with an abs.co. of 0.71, and the floor will have mineral fiber tiles with an abs.co. Of 0.66, all at 500 Hz.
An auditorium is 100m in length, 70m in width, and 20m in height. It is ventilated by a system that feeds in fresh air and draws out air at the same rate. Assume that airborne impurities form a well-stirred mixture. The ventilation system is required to reduce air pollutants present at any instant to 1% of their original concentration in 30 min. What inflow (and outflow) rate is required? What fraction of the total auditorium air volume must be vented per minute?
Civil engineering--Q17 - A metallic column is covered through 1 in. Thick (25.4 mm) spray implemented cementitious cloth. The use of the yankee exercise and the following records, decide the fireplace resistance R for the column:
A cold-storage warehouse is to be constructed of a number of individual rooms that are maintained at various temperatures. The walls of one room are constructed of 4 inches thick masonry on the outside of 0.5 inches thick plywood on the side. Sandwiched between the masonry and plywood is glass fiber insulation that is 3.5 inches thick. The inside-wall temperature is to be maintained at −10°F and the outside-wall temperature is 70°F. As a first step in sizing the required cooling unit, determine the heat flow the wall on a per-square-foot basis.
A steel tape, known to be of standard length at 25°C, is used in laying out a runway 1.5 km. long. Determine the temperature correction and the correct length to be laid out when the temperature is 38°C. complete solution pls thank u
a jet of watee issuing from a nozzle at 80kph. Neglecting air resistance, how high could the jet of water rise?
Membrane filtration, operated in a dead-end mode, is used to treat secondary effluent. If the HPC in the effluent increased from 5 org/L to 200 org/L, after an extended period of operation, estimate the number of broken fibers for the following conditions. The influent flowrate and organism count are 4000 m3/d and 6.7×107 org/L, respectively. The membrane bundle contains 5000 individual fibers. If the influent and effluent turbidity values under normal operation are 4 and 0.25 NTU respectively, estimate the increase in the effluent turbidity assuming the increase could be measured.
The air coming out of the distillery has 60% relative humidity. How much water will you need to saturate this airstream? After saturation* what will be the temperature and the total volumetric flow rate? Should you also provide soaker hoses in your design? Discuss the reasons why you will or will not include soaker hoses.