Answered: A signal is carrying data in which one…

A signal is carrying data in which one data element is encoded as one signal element (r 1). If the bit rate is 100 kbps, what is the average value of the baud rate if c is between 0 and 1?

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 30VE

See similar textbooks

Related questions

Q: Bit length can be defined in terms of a. high and low frequency b. Propagation Speed c. Bit duration…

A: Complete the statement given, Bit length can be defined in terms of Using one word from the…

Q: A channel has a bit rate of 4 kbps and a propaga- tion delay of 20 msec. For what range of frame…

A: The Answer is

Q: Data may be sent in both ways on the same signal carrier using this kind of data transfer. What does…

A: Full-Duplex is the data transmission mode in which the data can flow in both directions at the same…

Q: An Information system sends 365 kbps over a channel of 25 KHz bandwidth, how many signal levels…

Q: Sketch the signal to carry through the medium if the sequence of bits to send using AMI line…

A: We need to sketch the signal to carry through the medium if the sequence of bits to send using AMI…

Q: What is the maximum data rate of a channel with a bandwidth of 200KHZ if we use four levels of…

A: This question explains about the maximum data rate of a channel with a bandwidth of 200KHz if we use…

Q: For the following stream of digital signal which is being transmitted by bit rate 5 Kbps:…

A: a. Draw waveform for all line code is self synchronized or not.

Q: An analog signal is first encoded in binary PCM before being transformed to a multilevel signal for…

Q: In ADSL, if the baud rate is 4000 baud/sec with 10 bits per baud, then the downstream data BW will…

A: Bit Rate: Bit Rate is used for measuring data transmission speed Bit rate refers to the numbers of…

Q: Suppose each bit change in a 4-bit ADC represents a level of 0.15 m. What would the 4 bits be…

A: According to the information given:- we have to follow the instruction and find out the what would…

Q: A digital signaling system is required to operate at 512 Kbps. a. If an 8-bit word is used to encode…

A: The Answer is in given below

Q: How many bits per second can be sent over a communications system that has a baud rate of 4800 with…

A: The number of bits sent per second over a communications system with baud rate, B, and number of…

Q: Assume that two data element is carried by one signal elements, calculate the value of signal rate…

A: Answer is None of the above. the right answer is 0.25 Mbaud. Explanation is in step 2.

Q: signal is carrying data in which one data element is encoded as one signal element (r = 1). If the…

A: The formula used here is s=C*N*(1/r) here N=200kbps which is 200000 r=1

Q: An analog signal carries 4 bits in each signal unit. if 1000 signal units are sent per second, then…

A: Introduction :Given , signal carries 4 bits in each signal unit.1000 signal/sec sent .Then , we have…

Q: blw 4 In FM modulation ,the amplitude of the carrier wave is varied in proportion to the amplitude…

A: In frequency modulation, the frequency instead of the amplitude of the carrier wave is made to vary…

Q: A channel has a bit rate of 4 kbps and one-way propagation delay of 20 ms. The channel uses stop and…

A: Introduction:Channel bit rate = 4 kbps1-way propagation delay = 20 msProtocol used = Stop &…

Q: Q3. A signal is carrying data in which one data element is encoded as one signal element (r = 1). If…

A: Note: As per Bartleby's answering guidelines, only one question can be answered at a time. Hence, Q3…

Q: In PCM, if the sampling rate = 1500 sample/sec and each sample is encoded using 3 bits, what will be…

A: The bit rate of a PCM signal can be calculated as number of bits per sample X sampling rate

Q: A digitized voice channel is made by digitizing a 4-kHz bandwidth analog voice signal. We need to…

A: Given the message signal Bandwidth B= 4MHz We know that B = 2fm, so, fm = 4MHz/2 fm = 2MHz

Q: Assume having a low-pass noiseless channel that spans from a Frequency of 0Hz to 130Hz, to send at a…

A: please upvote for my efforts thanks! answer: bit rate= 2* bandwidth * log2(number of levels)

Q: Q6: Suppose the carrier waveform illustrate below with assuming a group of 10 information signals xi…

A: ANSWER:-

Q: The information density of QPSK, 8PSK and 8QAM modulation schemes with 8 Kbps data rate respectively…

A: In M-ary modulation, we can preserve bandwidth if we keep the symbol rate the same while increasing…

Q: 30. An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements…

A: Answer: b. 3 bits baud

Q: A channel has a bit rate of 4 kbps and a propagation delay of 20 msec. For of frame sizes does…

A: The Answer is in below Steps

Q: What is the average data rate of a signal transmitted at 36 kbauds and with 4 bits transmitted per…

A: No of bits transmitted => n = 4 The average data rata of a signal transmitted at 36 kbauds with 4…

Q: The maximum number of T-1 carrier signals that can be transported by a SONET STS-1 frame is,

A: According to the question we need to solve the given 5 Questions.

Q: The maximum data rate that a medium of 10 KHz and S/N ratio of 30 dB is roughly: Select one: О а.…

A: The maximum data rate that a medium of 10 Khz and S/N ratio of 30 dB is roughly

Q: Consider a full-duplex 256 Kbps satellite link with a 240 millisecond end-to-end delay. The data…

A: The answer is

Q: A DMS has a message consists of 11 equally likely symbols. Then it extends the message to the order…

A: ANSWER:-

Q: If the received signal level for a particular digital system is -151 dBW and the receiver system…

A: ANSWER:-

Q: A digital signal system is required to operate at 9600 bps, If a signal element encodes a 4-bit…

A: Solution: Channel capacity = 9600 bps. The signal element encodes a 4-bit word. This means that,…

Q: Given a channel with an intended capacity of 20 Mbps, the bandwidth of the channel is 3 MHz. what…

A: Given data: Bandwidth (B) = 3MHZ Intended capacity of the channel(C) = 20 Mbps

Q: If the bit rate for a 16-QAM signal is 4000 bps, what is the baud rate?

A: Ans:- Baud rate is 1000

Q: Sketch the signal to carry through the medium if the sequence of bits to send using Differential…

A: In Differential Manchester Encoding the Bit 0 represent Inversion whereas 1 represents no inversion.…

Q: Assume having a low-pass noiseless channel that spans from a Frequency of OHz to 180HZ, to send at a…

A: please do upvote for my efforts ! answer: bit rate = 2* bandwidth * log2(number of levels)

Q: Draw the waveform for the three-byte data sequence Ox93, 0x11, Ox41 being transmitted by UART at…

A: It is defined as a image that represents an audio signal or recording. It shows the changes in…

Q: An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are…

A: The Answer is

Q: Time-Division Multiplexing (TDM): On Example 6 Slide 8. Assume that the data rate for each input…

A: Given: assuming that the data rate of each input connection is the character produced by each source…

Q: Baseband transmission of a digital signal is possible only if we have a ____ channel.

A: Baseband Transmission is defined as sending a digital signal over a channel without changing the…

Q: In 8 bit data transmission system the transmitted data X, Y and Z after adding an EVEN Parity. The…

A: Given 8 bit transmission system the transmitted data X,Y,Z after adding an EVEN parity and we need…

Q: The minimum bandwidth required to send a digital signal of bit rate 500 kbps is roughly equal to…

A: Given: The minimum bandwidth requires to send a digital signal of bit rate 500 kbps equal to…

Q: Timing error occurs in synchronization as a result of frequency difference between two physically…

Q: The modulating frequency of an FM signal, with modulation index 2.5 and maximum deviation of 25 KHz…

A: Modulation Index is the ratio of frequency deviation and modulating frequency

Question

A signal is carrying data in which one data
element is encoded as one signal element (r
1). If
the bit rate is 100 kbps, what is the average
value of the baud rate if c is between 0 and 1?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Explanation

VIEW

Step 2: Answer

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

A signal is carrying data in which one data element is encoded as one signal element (r = 1). If the bit rate is 200 kbps, what is the average value of the baud rate if c is between 0 and 1?
An analog signal carries 8 bits per signal element. If 6000 signal elements are sent per second, find the bit rate.
The transmission of data makes use of both periodic analog signals and non-periodic digital signals; why is this the case?
Data communication Suppose that the spectrum of a channel is between 8 MHz and 10 MHz, and the intended capacity is 8 Mbps. 1= With multiple signaling level, how many levels are required to obtain this capacity and how many bits can be transferred with each signal element? Constant values= c=3x^10°m/s, k=1,38x^10231/K
In _______ encoding, the duration of the bit is divided into two halves. The voltage remains at one level during the first half and moves to the other level in the second half. The transition at the middle of the bit provides synchronization. a. Manchester b. differential Manchester c. both (a) and (b) d. neither (a) nor (b)
a. Compute for the data efficiency of transmitting if the data format is a General Synchronous Data Frame. b. For an asynchronous data transmission (wherein 1 byte of data is accompanied by a specific number of auxiliary bits), how many start and stop bits are there if the data efficiency in transmitting is ? The number of start bits is equal to the number of stop bits.
Match the given baud rate and the number of bits carried by each signal unit (baud rate, bits) with the bit rate. choose between : 1200 , 3600 , 3200 1200, 3 Answer 1 600, 6 Answer 2 1200, 1 Answer 3 600, 2 Answer 4 800, 4 Answer 5
Suppose each bit change in a 4-bit ADC represents a level of 0.15 m. What would the 4 bits be for a level of 1.7 m? Suppose the 4 bits were 10002. What is the range of possible levels?