A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1480 mm². Assume a = 2.3 m, b = 7.8 m, and c = 3.3 m. If P = 40 kN and Q = 70 kN, determine the normal stress in each member. y Lx a P B b с

A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1480 mm². Assume a = 2.3 m, b = 7.8 m, and c = 3.3 m. If P = 40 kN and Q = 70 kN, determine the normal stress in each member. y Lx a P B b с

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm. Calculate the allowable force in rod (1).
Solve using method of consistent deformation; EI =4x10^6 KN m^2, L=3.0, Wo=20KN/m
The wide-flange beam is subjected to the loading shown in (Figure 1). Suppose that P = 40 kN. Follow the sign convention. a) Although it is not very accurate, use the shear formula to determine the shear stress developed at point A b) Determine the principal stress σ1 at point A c) Determine the principal stress σ2 at point A
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at top of the beam section at 3.09 from the support. (MPa) Properties: Beam width = 259 mmBeam height = 447 mmPu = 63.85 kNSpan of the beam = 10 mPrestressing force = 502 kNeccentricity = 96 mm
For the beam in question 1, determine the maximum bending and shear stressesat point C, at point P of the section. Represent the stress cube
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1600 mm2. Assume a = 2.4 m, b = 9.1 m, and c = 3.5 m. If P = 40 kN and Q = 90 kN, determine the normal stress in each member.
the cantilever has a partially hollow circular cross section. If the admissible normal stress is 140 MPa, determine the maximum value of Wo (distributed load intensity) that the beam can support. express your answer in KN / m
Solve using Force Method- Consistent Deformation. (Both support are fixed) 1. Solve for reactions 2. Draw M, m1,m2,m3 3. Compatibility Equations 4. Value of x1, x2, x3
NO. 4. The 150-kg bucket is suspended from end E of the frame. Determine the average normal stress in the 6- mm diameter wire CF and the 15-mm diameter short strut BD IN Figure 4.
If d = 450 mm, determine the absolute maximum bending stress in the overhang beam.