A simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the beam properties are given below, what is the final stress at bottom of the beam section at a distance 1.51m from the right support where the total losses of the prestressing force is 22% (MPa) Properties: Beam width = 256 mm %3D Beam height = 461 mm %3D Varying load = 8.41 kN/m %3D Uniform load = 4.73 kN/m !! x = 3.08 mm y = 6.85 mm Prestressing force 460 kN eccentricity = 101 mm %3! %3D VL (kN/m) UL (kN/m) y

A simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the beam properties are given below, what is the final stress at bottom of the beam section at a distance 1.51m from the right support where the total losses of the prestressing force is 22% (MPa) Properties: Beam width = 256 mm %3D Beam height = 461 mm %3D Varying load = 8.41 kN/m %3D Uniform load = 4.73 kN/m !! x = 3.08 mm y = 6.85 mm Prestressing force 460 kN eccentricity = 101 mm %3! %3D VL (kN/m) UL (kN/m) y

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed joint and B is the sliding joint. This beam is made of a ductile material with a yield stress (σak) of 1000 MPa. The thickness (depth) of the beam profile is t=6 mm. A) As a mechanical engineer, check the strength of this beam (in terms of Normal and Shear Stress) ? B) In order for the existing beam to run smoothly, two 100x25 mm plates made of the same material are planned to be welded to this beam. The mechanical engineer working in the factory told the welder to weld this piece under the beam (where the B point is). But the welder, regardless of what the mechanical engineer said, welded this plate to both sides of the existing T-section beam as shown below, thinking that it wouldn't matter anyway. As a mechanical engineer : 1) After welding these plates on both sides of the beam, as the welder did, find out whether the new beam will work smoothly or not by making the necessary…
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
%D A cantilever beam has a cross-section and concentrated loads P1 = 30 kN and P2 = 10 kN, as shown. Write all answers in 2-decimal places. 35 mm 250 mm P1 P2 35 mm B 500 mm 1.8 m 3.2 m
8. Given an axial failure stress of 2000 psi, a factor of safety of 1.67 and modulus of elasticity = 1800 kslydetermine the maximum square brace size (b (in.) x b (in.)) in the brace resisting the largest force.
P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam width of 130mm and a height of 200mm. Assuming values of P = 25KN, w = 30 kN/m, and E = 5m, determine: 1) The max tensile bending stress in MPa (enter this value into D2L answer box, in MPa). Exactly where does this occur along the beam? (4 sigs) 2) The max shear stress in MPa. Exactly where does this occur along the beam? ( 4 sigs) Your Answer:
Determine the stress concentration factor for the beam shown below that has a fillet to the larger diameter knowing that: Material modulus of elasticity = 208 GPa Diameter D = 75 mm Length L = 550 mm Normal strain at the base of the fillet (from strain gage reading on the top of the beam) = 0.0005 Load P = 5.00 kN Moment of inertia for a circular section is %3D %3D R* /4
For the cantilever beam shown. find the value of Normal stress due to axial load at :point F FO ce A 10 m Diameter 100 mm 6 KN.m No stresses at point D 0 -31.229 Mpa +40.99 Mpa -0.25 Mpa +40.49 Mpa No stresses at point F No stresses at point A No stresses at point B +0.25 Mpa +40.74 Mpa No stresses at point C -40.99 Mpa +31.229 Mpa -40.74 Mpa +30.55 Mpa -40.49 Mpa +0.679 Mpa -0.679 Mpa No stresses at point E -30.55 Mpa
The unknown load P is acting eccentrically with respect to the horizontal and vertical axes of the I-section shown. Knowing that the horizontal eccentricity is a = 1.25 in. and the vertical eccentricity is 2.5 in. determine the largest value of P that can be applied without exceeding either of the following tensile andcompressive allowable stresses:σten = 10 ksiσcomp = 18 ksi
A 10-m simply-supported beam having the cross section as shown supports a uniformly distributed load w (weight of the beam assumed to be part of w) and concentrated load of 10 KN at midspan. The beam has an allowable compressive stress 150 MPa and an allowable tensile stress of 50 MPa. Do the following a. Recommended value of the dimension b so that stresses will be reached simultaneously points - For the recommended value of b correctly computed - For the moments of Inertia with respect to the centroid of the section based on the recommended value of b b. Compute the magnitude of the maximum w that can be supported - For correctly drawn shear diagram indicating magnitude at every change of load positions. - For correctly drawn moment diagrams indicating magnitude at every change-of-load positions - For the computation of the magnitude of the maximum w that can be supported - 50 10 KN W (KN/m) 50 10m H 20->> b 160 20
Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
The normal and shear stresses in a bar must be limited to σmax and τmax. Each limit is used to calculate a required cross-sectional area for the bar. Which of the two cross-sectional areas should the designer use?
A cantilever beam with a ‘T’ shaped cross-section is loaded with a distributed load as shown below.The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm.Parameter Description Value UnitsL - Beam length 250 mma - Width of the flange 80 mmd - Height of the web 75 mmσ - Yield stress 250 MPaYou are tasked with ensuring the beam can withstand the applied loading. To do this you must:a) Calculate the centroid for the given cross-section. Your value of ?ത should be measured fromthe bottom of the section. Determine an expression for Q (statical moment of area) for thegiven shape. The expression(s) for Q should be in terms of the variable, y, measured from thebottom of the section. b) Create a graph of the shear and bending stresses at the fixed support (B) over the crosssection. The stresses should be plotted as a function of y, measured from the bottom of thesection.