A simply supported beam supports the loads shown in Fig . 29.35a . The cross - sectional dimensions of the wide - flange shape are shown in Figure (a) Determine the maximum shear force in the beam. (b) At the section of maximum shear force , determine the shear stress in the cross section at point H, which is located 100 mm below the neutral axis of the wide - flange shape. (c) At the section of maximum shear force , determine the maximum horizontal shear stress in the cross section 200 mm 15 mm y 25 kN 50 kN/m 10 mm B 300 mm 100 mm 2 m 6 m

A simply supported beam supports the loads shown in Fig . 29.35a . The cross - sectional dimensions of the wide - flange shape are shown in Figure (a) Determine the maximum shear force in the beam. (b) At the section of maximum shear force , determine the shear stress in the cross section at point H, which is located 100 mm below the neutral axis of the wide - flange shape. (c) At the section of maximum shear force , determine the maximum horizontal shear stress in the cross section 200 mm 15 mm y 25 kN 50 kN/m 10 mm B 300 mm 100 mm 2 m 6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the distribution of the shear stress over the cross section of the beam shown in Fig.a
Q2: For the cantilever beam with uniformly distributed load shown in Figure , determine the following: 1. The maximum shear force in the beam in (kN) 2. The maximum bending moment in the beam in (kN.m) 3. The area of the section in (mm) 4 The moment of inertia about the centroidal x axis 5.The maximum shear stress at section I in (MPa) 6.The maximum shear stress at section 2 (within the flange) in (MPa) 7.The maximum shear stress at section 2 (within the web) in (MPa) 8. The maximum shear stress at section 3 (at the neutral axis) in (MPa) 9. The average shear stress on the section (MPa)
The beam is subjected to a point load and a distribution load as shown in Figure 3-1 below.(a) Find the reaction from supports B and E.(b) Draw a beam's Shear Force Diagram.(c) Draw the moment diagram of the beam.(d) If the cross-sectional area is shown in Figure 2-2, how many mm is the neural axis NA from the bottom? (e) Find the second moment of area, INA from the neural axis.(f) Find the maximum shear stress max from the beam.(g) Find the maximum tensile flexural stress max T and maximum compressive flexural stress max C on the beam, respectively.
A beam with the cross-section shown in Figure Q2 is exposed to a transverse load (Q) of magnitude 5 kN acting vertically downward through its centroid. (i) Develop the general expression for the distribution of transverse shear stresses in the web of a transversely loaded beam with the I cross-section shown in Figure Q2. (ii) Use the developed expression in (i) above to determine the stresses in the web at the horizontal centroidal axis of the cross-section, and at the intersections of the web and flanges. (iii) Develop the general expression for the distribution of transverse shear stresses in the flanges of a transversely loaded beam with the I cross-section shown in Figure Q2.
a) In Figure 5, cantilver beam AB supports a uniformly distributed load of 2kN/m and twi concentrated load P and Q. It has been experimentally determined that the normal stress due to bending on the bottom edge of the beam is -56.9MPa at A and -29.9MPa at C. i) Determine the magnitudes of load P and Q. ii) Draw the shear and bending-moment diagrams for the beam. iii) Calculate the changes for load P and Q if the uniformly distributed load was increased to 4kN/m?
For the beam in figure: 1. Compute the maximum shearing stress devloped in the beam. 2. Determine the shear stress in a fiber located at y1 = 26 mm , from the bottom for section 2 m from the left end of the beam.
A column with a wide-flange section has a flange width b = 200 mm , height h = 200 mm , web thickness tw = 8 mm , and flange thickness tf = 12 mm (Figure 1). Calculate the stresses at a point 75 mm above the neutral axis if the section supports a tensile normal force N = 2.9 kN at the centroid, shear force V = 4.6 kN , and bending moment M = 4.8 kN⋅m as shown (Figure 2). Calculate the magnitude of the shear stress at the point due to the internal shear on the section. τ =?
A rectangular beam is subjected to a pure bending moment M. The cross-section of the beam is shown in Fig. 1.34. Using the elementary flexure formula, determine the normal and shearing stresses at a point (x, y) on the plane AB shown.
On the recessed, rectangular cross-sectional beam, the forces F1 = 50 kN, F2 = 100 kN, F3 = 70 kN are applied. If Young's modulus and shear modulus are 120 GPa and 44.5 GPa respectively, find the strain that the strain gauge that forms an angle theta = 30 ° with the x-axis should record. Consider that L1 = 60 cm, L2 = 120 cm, h = 5 cm, b = 10 cm
5. The beam ABCD with a rectangular cross section carries the loading shown in the figure. Determine the magnitude and location of the maximum bending stress in the beam.
Determine the reactions and draw the shear and bending moment diagrams for the beams shown by using the consistent deformation method.
Question 5 If the simply supported beam is subjected to the load shown below, determine the followings: a- The vertical reactions acting at A and B. b- The internal shear force acting on the cross-section through point C. c - The internal bending moment acting on the cross-section through point C. d- The shear stress at section C.