A simply supported beam with spans of LAB = 7 ft and LBC = 21 ft supports loads of w = 7.5 kips/ft and P = 27 kips. The cross-sectional dimensions of the wide-flange shape are b= 10.0 in., tf = 0.54 in., d = 28.3 in., and tw = 0.42 in. Determine the magnitude of: (a) the maximum horizontal shear stress in the beam. (b) the maximum bending stress in the beam. W B LBC LAB Answer: (a) Tmax= (b) Omax= ksi ksi

A simply supported beam with spans of LAB = 7 ft and LBC = 21 ft supports loads of w = 7.5 kips/ft and P = 27 kips. The cross-sectional dimensions of the wide-flange shape are b= 10.0 in., tf = 0.54 in., d = 28.3 in., and tw = 0.42 in. Determine the magnitude of: (a) the maximum horizontal shear stress in the beam. (b) the maximum bending stress in the beam. W B LBC LAB Answer: (a) Tmax= (b) Omax= ksi ksi

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

The Beam has a span of 9 m, fixed at both ends and carries a uniformly distributed load of w = 25 kN/m throughout its length. The beam is W 16 x 77 with the following properties: bf = 260 mm tf = 19.3 mm d = 420 mm tw = 11.6 mm Ix = 462. 02 x 106 mm4 Iy = 57.44 x 106 mm4 a. Calculate the maximum bending stress in the beam, in MPA. b. Calculate the average shearing stress in the web, in MPa.
A simply supported beam with spans of LAB = 14 ft and LBC = 42 ft supports loads of w = 6.5 kips/ft and P = 31 kips. The cross-sectional dimensions of the wide-flange shape are bf = 7.5 in., tf = 0.55 in., d = 29.2 in., and tw = 0.49 in. Determine the magnitude of: (a) the maximum horizontal shear stress in the beam. (b) the maximum bending stress in the beam.
If the T-beam is subjected to a vertical shear V = 14 kips, determine the maximum shear stress (ksi) in the beam Where: tf = 2.4 in and d = 7 in
The vertical load of 115 kN and horizontal load 125 kN are applied at joint F and B by using method of sections determine the force in member EG, DG and DF.
The steel beam has the cross-sectional area shown. if w = 6.5 kips/ft, determine the absolute Horizontal shearing stress (ksi) in the beam Where L1 = 9 ft; L2 = 8 ft; bf = 8.2 in and tw = 0.4 in
A simply supported beam with spans of LAB = 11 ft and LBC = 33 ft supports loads of w = 7.5 kips/ft and P = 33 kips. The cross-sectional dimensions of the wide-flange shape are bf = 8.0 in., tf = 0.54 in., d = 27.7 in., and tw = 0.43 in. Determine the magnitude of:(a) the maximum horizontal shear stress in the beam.(b) the maximum bending stress in the beam.
1. A 75 mm x 75 mm x 8 mm angle is used as a beam over a span of 7.0 m. It is subjected to loading of 10 kN/m acting in the vertical plane passing through the centroid of the Section Determine maximum stress induced in the section.
Hello can you please solve the maximum values of flexural and the horizontal shearing stress of the beam.
From the given simply supported beam below, determine the following: g. The shear stress at the mid-point of the beam.
A triangular wooden beam width 150 mm base and 300 mm height carries two concentrated load of 20 kN at third points. If the simple span of the beam is 6 m, 1. Compute the maximum shearing stress of the beam. a. 0.58 MPa b. 1.33 MPa c. 0.48 MPa d. 0.86 MPa 2. Compute the bending stress of the beam. a. 56.33 MPa b. 71.11 MPa c. 78.48 MPa d. 45.78 MPa
A box beam is constructed from four pieces of wood, glued together as shown. If the moment acting on the cross-section is 12 kN-m, determine the flexural stress in MPa at point A Where: tw = 22 mm; and d = 293 mm
The cantilever beam shown is subjected to a concentrated load of P. The cross-sectional dimensions of the wide-flange shape are also shown, where bf = 7.00 in., d = 14.0 in., tf = 0.475 in., tw = 0.350 in.(a) Compute the value of Q that is associated with point K, which is located yk = 3.5 in. above the centroid of the wide-flange shape.(b) If the allowable shear stress for the wide-flange shape is τallow= 13 ksi, determine the maximum concentrated load P than can be applied to the cantilever beam. Determine the moment of inertia Iz1 for the top flange (1) about the z centroidal axis of the cross-section.Answer: Iz1 = in.4. Determine the moment of inertia Iz2 for the bottom flange (2) about the z centroidal axis of the cross-section.Answer: Iz2 = in.4. Determine the moment of inertia Iz3 for the web (3) about the z centroidal axis of the cross-section. Note that the centroid of the web is also the centroid of the cross-section.Answer: Iz3 = in.4. Determine the…