A simply supported rectangular beam with dimension of h=550 mm and b: 250 mm is subjected to bending moment. The bending moment under the quasi-permanent combination of load effect, M, 72 kNm. Concrete strength grade is C30, and the beam is reinforced with 3 18 bars. The environment classification is I. Requirement: determine the maximum crack width.

A simply supported rectangular beam with dimension of h=550 mm and b: 250 mm is subjected to bending moment. The bending moment under the quasi-permanent combination of load effect, M, 72 kNm. Concrete strength grade is C30, and the beam is reinforced with 3 18 bars. The environment classification is I. Requirement: determine the maximum crack width.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

here are the answer, only need solutions 1.f = 11.46 MPa 2.Mcr= 88.90 kN-m 3.fconc= 17.14 MPa; fsteel= 318.20 MPa
A half-block concrete masonry unit is tested for compressive strength. Theoutside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 25 mm. Theload is applied perpendicular to the hollow cross section and the maximum load is 225 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
A half-block concrete masonry unit is subjected to compression until failure.The outside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 38 mm. The loadis applied perpendicular to the hollow cross section and the maximum loadis 296 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
For the below given beam: a) Determine the cracking distributed load. b) Determine the stress in concrete and steel under service load if WDL = 15 kN/m; WLL = 10 kN/m Materials: C25; S420 40 mm 1.8 m 560 mm 300 mm
Given the following properties of beam: b = 250 mm, d = 325 mm and h = 400 mm. a) Assuming the concrete is uncracked, compute the bending stresses (in MPa) in the extreme fibers of the beam at M = 100 kN-m. Blank 1 b) Determine the cracking moment (in kNm) for the section if f'c = 28 MPa. Blank 2 c) Compute the flexural stresses in the concrete and steel of the beam using the transformed-area method at M = 100 kN-m, n = 9 and reinforced with 5-16 mm diameter tension bars. Unit must be in MPa. fc = _Blank 3, fs =__________ Blank 4
60. If the loss of prestress is excessive resulting in tensile cracks, which method should be used? A. O Preloading method B. O Hollow method C. O Transparent method D. O Layered method
In post-tension, concrete should be hardened first before applying the tension in the tendons. True False
S Maximum strain in extreme fibre of concrete and in tension steel of Fe 415 grade (E = 2 x 105 N/mm²) in a balance section in limit state of flexure are respectively (a) 0.0035 and 0.0031 (b) 0.0035 and 0.0038 (c) 0.002 and 0.0042 (d) 0.002 and 0.0038
these are the answers I only need solutions 1. f = 8.42 MPa 2. Mcr= 121.0 kN-m 3. fconc= 10.42 MPafsteel= 197.22 MPaf’steel= 104.30 MPa