"A simply supported unreinforced concrete test beam spanning 1.8 m shown in the Figu below. The beam is of rectangular cross-section (100 mm width by 150 mm overall depth). Th beam failed when subjected to two-point loads of 4 kN as each, shown in the figure. The beam was made of normal-density concrete. Determine the moment of inertia of the gross cross- section of a concrete beam around the axis of bending?(mm^4)" 1/3 р 1/3 р 1/3 4 KS 100 mm 150 mm

"A simply supported unreinforced concrete test beam spanning 1.8 m shown in the Figu below. The beam is of rectangular cross-section (100 mm width by 150 mm overall depth). Th beam failed when subjected to two-point loads of 4 kN as each, shown in the figure. The beam was made of normal-density concrete. Determine the moment of inertia of the gross cross- section of a concrete beam around the axis of bending?(mm^4)" 1/3 р 1/3 р 1/3 4 KS 100 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.) The specific weight of the concrete is 150 ??⁄??3, and the coefficient of friction between the base of the dam and the foundation is 0.42. If the factor of safety against overturning is 2, compute for the minimum width of the dam. CHOICES a.) 8.416 b.) 4.681 c.) 6.841 d.) 1. 684 2.) The specific weight of the concrete is 150 ??⁄??3, and the coefficient of friction between the base of the dam and the foundation is 0.42. Use 1.5 as the factor of safety (F.S) against sliding. Calculate the width of concrete dam that is necessary to prevent the dam from sliding. Unit of the Correct Answer: ft CHOICES a.) 5,783 b.) 7.358 c.) 3.578 d.) 8.357
A short hollow cast iron column of external diameter 30 cm and internal diameter 28 cm is filled with concrete. The column carries a total load of 400 kN. If ECI = 150 GPa and EConc =25 GPa, calculate: (a.)The stress in cast iron and concrete. (b.)What must be the internal diameter of the cast iron column if a load of 450 kN is to be carried and stresses and external diameter of the column remain unchanged?
The floor system of a residential building consists of 125mm thick concrete slab (unit weight = 23.6 KN/m^3) resting on the three 8 m spanned RC floor beams spaced at 1.7 meters on center. Size of RC beam is 200mm x 450mm. NSCP 2015 load Factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the unfactored slab in KN/m? Express your answer in 1 decimal places.
a tank with its contents weighs a 5000kg. It will be supported by four concrete posts equally spaced and with outer edges flushes with the perimeter of the tank. The compressive strength of the concrete posts is 1000 psi and a factor of safety of 4 is required. calculate the diameter of each post in cm.
Base on the gravity load path shown above, explain what is occurring at each of the labeled points.
1. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 KN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa.
Briefly describe the three (3) correction procedure in axial and block point load test.
Pls answer, I'll rate. A concrete dam retaining water is shown. If the specific weight of concrete is 150 ??⁄??3, and the coefficient of friction between the base of the dam and the foundation is 0.42. Calculate the height of the dam that is necessary to prevent the dam from sliding. Use 1.5 as the factor of safety (F.S) against sliding.
A rectangular concrete beam 320 mm wide and 449 mm deep is simply supported over a span of 11.75 m. the beam is reinforced with straight tendons situated 56 mm above the bottom of the beam under a prestressing force of 631 kN. Concrete weighs 23.12 kN/m3 with modulus of elasticity Ec=21,212.29 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads.
Describe the categories of static load tests.
Select the magnitude of the self-weight of a lightened slab if the module has 145,000 cm3 of concrete per square meter and the lightener is removable.
calculate the corresponding depth of uniform stress block in a reinforced concrete beam 45x10 deep reinforced with bars 20mm in diameter enclosed with 10-mm-dia stirrups when the tensile steel strain is 0.008 and concrete compression strain is 0.003 f’c=27MPa