A single pass rice mill was tested for 30min. and gave the following results: input paddy 10000 kg, milled rice produced-6,500 kg, broke produce 1500 kg and weight of headrice-2000 kg. Compute the following: (a) Throughput capacity, (b) % Milling recovery, (c) Broken grain, and (d) % Head rice recovery.

A single pass rice mill was tested for 30min. and gave the following results: input paddy 10000 kg, milled rice produced-6,500 kg, broke produce 1500 kg and weight of headrice-2000 kg. Compute the following: (a) Throughput capacity, (b) % Milling recovery, (c) Broken grain, and (d) % Head rice recovery.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

A leaf filter filtering a slurry, gave a total of 8 m³ filtrate in 30 minutes. Filtration was continued till 11.3 m³ of filtrate was collected. Estimate the washing time in minutes, if 11.3 m³ of wash water are used. The resistance of the cloth can be neglected and a constant pressure is used throughout.
The present pumping rate of crude oil through the Alaska Pipeline with an ID of 39 in is 550,000 barrels per day (1 barrel is 42 U. S. gallons). For crude oil at 60ºC, take ρ = 860 kg/m3 and μ ≈ 0.004 kg/m·s. What would be the maximum rate if the flow were constrained to be laminar? Take π = 22/7. Answer is asking for maximum flow rate for barrels per day
A small blood vessel near the skin surface has a radius of 10 µm, a length of 1 µm and the pressure drop along the blood vessel is 2.50 Pa. The viscosity of blood is 0.0027 Pa.s. What is the volume flow rate of blood through this blood vessel? What is the velocity of blood flow? Vasodilation causes the radius of this blood vessel to increase to 12 µm, while leaving the pressure drop along the vessel unchanged? What is the volume flow rate through this blood vessel now? What is the velocity of blood flow?
5. The total head of a fan is 185 m and has a static efficiency pressure of 210 mm of water gage.What is the velocity of air flowing if the density of air is 1.15 kg per cubic meter? 8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of…
The total design and construction cost for a digester to handle a flow rate of0.5 million gallons per day (MGD) was $1.7 million in 2006. Estimate the costtoday for a flow rate of 2.0 MGD. The exponent from as shown for the MGDrange of 0.2 to 40 is 0.14. The cost index in 2006 of 131 has been updated to225 for this year.
Your team is designing a chemical processing plant. You are the liquid handling and transportation specialist, and you need to transport a solvent (μ = 3.1 cP, ρ = 122k kg/m3) from a storage tank to a reaction vessel. Due to other equipment constraints, the fluid velocity must be 0.8 m/sec, and you must use stainless steel piping (ε = 0.00015 mm) with a total length (L) of 12 m. Determine the pipe inner diameter (ID) you will need to achieve a pressure drop of 0.3 kPa. Use the Moody chart.
Tractor mounted sprayer having 14 nozzles 60 cm apart is moving at a forward speed of 35 km/h. The chemical mixed with water is to be applied at the rate of 75 lit /ha, at pressure of 500 kPa calculate the following-a) The rate of spray per nozzle in litminb) Pump efficiency if liquid lost in the system is 10%.c) Horsepower of engine if the pump and Power required for agitating the water 1/10th of rated power of engine c) height of Spray from the ground if the spray angle is 60 degrees & each nozzle should Spray 25 % more than nozzle Spacing
a. What is the Static efficiency of the fan if the air flow rate is equal to 3.8 5m /sec, total head of 68.72 m, velocity head of 30.86 m, mechanical efficiency and power are 39.12% and 35.72 KW at 30.69°C, respectively. b. Solve for the area at entrance of the fan blade, if the it has a 346mm diameter, flow of air is equal to 23.328 m/se and flow rate of 3.05 m³ /second.
The wind turbine gives the following data: Blade length, l = 39 m, Wind speed, V= 12.4 m/s, Air density, ρ = 1.23 kg/m3 , Power Coefficient, Cp = 0.39, Calculate the power available in the wind.
Design the high rate trick long filters for the following data. i)Sewage flow = 23.5 M.L/d ii)Recirculation ratio = 1.5 iii)BOD of row sewage =250 mg/l iv)BOD removal in primary tank = 30% v)Final efficient BOD desired = 30 mg/l
21_Cd calculated in flow over weirs represent Select one:a. Factor for calibrationb. The difference between actual flow and theoretical flowc. Water flow peak factord. Factor of turbulence of water flow 22_Thermal conductivity factor depends on Select one:a. Size of materialb. All of themc. Type of materiald. Density of material 23_Cooling is used in thermal conductivity test to Select one:a. To cool the device from over heatingb. Allow for thermal flow over the materialc. Noned. Cooling is not used in this exp 24_The device with highest static head loss is Select one:a. No static head loss in this experiment b. Venturi meterc. Orifice pland. Rotameter 25_Hand pump in flow measurement devices used to Select one:a. Noneb. To create pressurized water flowc. To clean the devicesd. To reset the manometers 26_If surface is not leveled under the center of pressure tank Select one:a. Legs of the device can be rotated to create level surfaceb. Items should be added under the device to…
a. Given the static head of 28.91 m, and static pressure head of 3.15 cm WC. What is the normal pressure, Pn? b. What is the Static efficiency of the fan if the air flow rate is equal to 3.8 5m /sec, total head of 68.72 m, velocity head of 30.86 m, mechanical efficiency and power are 39.12% and 35.72 KW at 30.69°C, respectively. c. Solve for the area at entrance of the fan blade, if the it has a 346mm diameter, flow of air is equal to 23.328 m/se and flow rate of 3.05 m³ /second.