A single-phase 100KVA, 1400/200 volt, 50 Hz, distribution transformer is used as a step- down transformer. The inductive load, which is connected to the secondary winding, absorbs 12KVAR and no active power. Assuming an ideal transformer with a 1500 volts, 60HZ source on primary terminals, calculate the load inductance in mH.

A single-phase 100KVA, 1400/200 volt, 50 Hz, distribution transformer is used as a step- down transformer. The inductive load, which is connected to the secondary winding, absorbs 12KVAR and no active power. Assuming an ideal transformer with a 1500 volts, 60HZ source on primary terminals, calculate the load inductance in mH.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4P: A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Similar questions

A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit equivalent circuit shown in part (c) contains an ideal transformer which cannot be accommodated by some computer programs. (a) True (b) False (ii) In the - circuit representation for real c in part (d), the admittance parameters Y11 and Y12 would be unequal. (a) True (b) False (iii) For complex c, can the admittance parameters be synthesized with a passive RLC circuit? (a) Yes (b) No
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
A transformer with a 10:1 ratio and rated at 60kVA, 2200/220V, 60Hz is used to step down the voltage of a distribution system. The low tension voltage is to kept constant at 220V. (a) What load Impedance connected to the low-tension side will be loading the transformer fully at 0.8 power factor (lag) ? (b) What is the value of this impedance referred to the high tension side?
A 2,300/240-V, 60-Hz, 4.6-kVA transformer isdesigned to have an induced emf of 2.5 V/turn.Assuming an ideal transformer, finda. The numbers of high-side turns Nh and low-sideturns Nl .b. The rated current of the high-voltage side Ih.c. The transformer ratio when the device is used as astep-up transformer.
630kVA 31500/400 DY 50Hz transformer has no load and short circuit tests power measurements are given as 1kW and 20kW respectively. Under the fourth of the nominal load with 0,85 capacitive power factor, calculate the efficiency of the transformer at nominal voltage as %?
A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240 V secondary winding, absorbs 80 kVA at 0.8 power factor lagging and is at 230 V. Assuming an ideal transformer, calculate the following:(a) primary voltage;(b) load impedance;(c) load impedance referred to the primary;(d) the active and reactive power supplied to the primary winding.
A Transformer with 10:1 ratio and rated at 50-kVA, 2400/240-V, 50-Hz is used to step down the voltage of a distribution system. The low-tension voltage is to be kept constant, if the transformer has: R = 2.2 0, R2 = 0.014 Q, X, = 4.1 0, X2 = 0.03 0, then, a. What load impedance connected to low-tension side will be loading the transformer fully. b. Calculate the equivalent resistance as referred to primary. c. Calculate the equivalent reactance as referred to primary. d. Calculate the equivalent impedance as referred to primary. e. Calculate the total Cu loss.
A 2000/400 V, 100 kVA, 60 Hz step-down single-phase transformer has a primary and secondary resistances of 0.2ohm and 0.05 ohm respectively, the corresponding leakage reactances being 0.3 ohm and 0.01 ohm respectively.1. Calculate the equivalent resistance, reactance and impedance referred to the low-voltage (secondary) side.2. Find the high (primary) voltage when the transformer is supplying full-load current at rated secondary voltage at 0.8 powerfactor lagging.3. Draw the phasor diagram showing your answer in 2.
1) A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240 V secondary winding, absorbs 80 kVA at 0.8 power factor lagging and is at 230 V. Assuming an ideal transformer, calculate the following: (a) primary voltage;(b) load impedance;(c) load impedance referred to the primary;(d) the active and reactive power supplied to the primary winding.